05-22-2011
Actually I have not only resetsc, but I have also upgraded the entire firmware. I'm still getting the error message repeatedly
10 More Discussions You Might Find Interesting
1. Solaris
I recently got this new old server from a friend. I just installed a fresh version of Solaris 10 on it. I have put a static IP of 192.168.100.10 the server. Their is no subnetting scheme on the network. And I made the hostname "SunServ." And I also changed the folder "/etc/inet/hosts" because I... (4 Replies)
Discussion started by: louisd11
4 Replies
2. Solaris
Hi all,
I am getting the below error on Solaris sunfire v245 server
Error: can not display this video mode
optimum resolution 1024x768 60Hz
i am not able to resolve this .plz help me out ? (1 Reply)
Discussion started by: saurabh84g
1 Replies
3. Solaris
Hi all,
I have a T2000 server which does not seem to respond when I power it on. Looking on the console I see the following:
SC Alert: Host Power Failure: MB_DC_POK Fault
SC Alert: Host system poweron failed due to fault at MB/FF_POK.
SC Alert: VOLTAGE_SENSOR at MB/V_VCORE has exceeded... (4 Replies)
Discussion started by: jambalaya
4 Replies
4. Solaris
Hi,
I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds.
I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this?
AVAILABLE DISK SELECTIONS:
0.... (12 Replies)
Discussion started by: honmin
12 Replies
5. Solaris
Hi Guyz,
I recently downloaded sol-10-u6-ga1-sparc-dvd.iso from Sun. I burned the disk as cd .iso.
When trying to boot at the ok> boot cdrom
i get the following error:
-----------------------------------------------------------------------
Boot device:... (2 Replies)
Discussion started by: Mwamba
2 Replies
6. Solaris
Hi all!
I've a machine - SunFire V890, it've been failed by OS error for 2 weeks ago, and now, I must reinstall OS (Solaris 10 2009), the progress was successful, but when I reboot, it displayed the error like :
Error -256: Last trap memory ... access aligned
Error -256: Last trap memory... (1 Reply)
Discussion started by: trantuananh24hg
1 Replies
7. Solaris
I work with a network management tool, which, for various reasons, is installed on a solaris server.This is a Sunfire T2000 server with 16 CPUs and 8GB of RAM. I have installed a Solaris 10 ZFS and 8GB swap. From the beginning I had problems with memory occupation that it rises progressively to 95%... (4 Replies)
Discussion started by: drusa79
4 Replies
8. Hardware
Recently the rear fan assembly of one of our T2000 servers went faulty. I could replace it immediately with the one from a currently powered off standby machine. But now this one has to be replaced.
So I got a quote from our supplier who charges EUR 776 for a new spare part or EUR 405 (all... (0 Replies)
Discussion started by: hergp
0 Replies
9. Solaris
I got a Power supply failure. I replaced the power supply and still got the error.
Any ideas on what I should try next? (1 Reply)
Discussion started by: 642fiddi
1 Replies
10. Hardware
I've recently bought an SunFire V245.
2x 2.5ghz x64
4gb ram
4x 73gb sas hdd
and... an blinking 'Identifior led' (white) with 'Service led' (amber) simultaneously.
It boots for +- 5 secs and then the error occurd.
Things done:
Removed all hdd.
Switched cpu
Switched/removed ram... (2 Replies)
Discussion started by: niswier2222
2 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)
NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS
--predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO
bup-midx(1), bup-save(1)
BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown- bup-margin(1)