Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
I tried to set the Mode Switch to the service position, but no use.
Please help! Thank you!
Last edited by aixlover; 05-13-2011 at 09:18 AM..
Reason: add more info
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
Hi, I am now trying to setup XSCF mail reporting for a Sun M5K. There is no mail server here. Each Sun box is both its mail receiver and sender by using mailx. Mailx is working fine on this M5K.
XSCF> setsmtp
Mail Server :
Port :
Authentication Mechanism :
Reply Address:
What should I... (4 Replies)
Hi,
This Sun M5000 currently has a single domain (0) created. Solaris 10 is installed on this domain with some local zones. Now we need to add a secondary hardware domain (1) to this M5000. My question: Can we keep the current OS settings on domain 0 when adding the secondary domain 1?
... (0 Replies)
Hi,
This Sun M5000 currently has a single domain (0) created. Solaris 10 is installed on this domain with some local zones. Now we need to add a secondary hardware domain (1) to this M5000. My question: Can we keep the current OS settings on domain 0 when adding the secondary domain 1?
Thank... (5 Replies)
Hi,
I've configured this Sun M5000 to use two system domains (added a second domain to it). The following is the info about the settings. The showdevices command can't show devices on domain 1 because Solaris is not loaded on it yet.
My question: How can I confirm the hardware devices such as... (5 Replies)
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT DEBIAN
pam_issue
PAM_ISSUE(8) Linux-PAM Manual PAM_ISSUE(8)NAME
pam_issue - PAM module to add issue file to user prompt
SYNOPSIS
pam_issue.so [noesc] [issue=issue-file-name]
DESCRIPTION
pam_issue is a PAM module to prepend an issue file to the username prompt. It also by default parses escape codes in the issue file similar
to some common getty's (using x format).
Recognized escapes:
d
current day
l
name of this tty
m
machine architecture (uname -m)
machine's network node hostname (uname -n)
o
domain name of this system
release number of operating system (uname -r)
current time
s
operating system name (uname -s)
u
number of users currently logged in
U
same as u except it is suffixed with "user" or "users" (eg. "1 user" or "10 users")
v
operating system version and build date (uname -v)
OPTIONS
noesc
Turns off escape code parsing.
issue=issue-file-name
The file to output if not using the default.
MODULE TYPES PROVIDED
Only the auth module type is provided.
RETURN VALUES
PAM_BUF_ERR
Memory buffer error.
PAM_IGNORE
The prompt was already changed.
PAM_SERVICE_ERR
A service module error occurred.
PAM_SUCCESS
The new prompt was set successfully.
EXAMPLES
Add the following line to /etc/pam.d/login to set the user specific issue at login:
auth optional pam_issue.so issue=/etc/issue
SEE ALSO pam.conf(5), pam.d(5), pam(7)AUTHOR
pam_issue was written by Ben Collins <bcollins@debian.org>.
Linux-PAM Manual 06/04/2011 PAM_ISSUE(8)