04-24-2011
it's solaris 9... there is NO "dladm" command!
Quote:
I have a Sun Blade 2500 with SUN 5.9 OS installed.
This User Gave Thanks to DukeNuke2 For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
Discussion started by: p4cldba
4 Replies
2. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Solaris
Hi all,
I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me.... (5 Replies)
Discussion started by: Smiling Dragon
5 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT OPENSOLARIS
wpad
wpad(1M) System Administration Commands wpad(1M)
NAME
wpad - WPA and WPA2 protocol daemon
SYNOPSIS
/usr/lib/inet/wpad [-i interface] [-k pre_shared_key_name]
DESCRIPTION
The wpad daemon provides common client functionality for the WiFi Protected Access (WPA) versions 1 and 2, as defined by IEEE802.11i stan-
dard. WPA was created by the WiFi Alliance, an industry trade group. WPA implements the majority of the IEEE 802.11i standard, and was
intended as an intermediate measure to take the place of Wired Equivalent Privacy (WEP) while 802.11i was prepared. WPA2 implements the
full standard.
wpad provides the following WPA/IEEE 802.11i features:
o WPA-PSK ("WPA-Personal")
o Key management for CCMP, TKIP, WEP104, WEP40
Stop and start the wpad daemon using dladm(1M). Use:
# dladm connect-wifi
...to start the wpad daemon. Use:
# dladm disconnect-wifi
...to stop the daemon.
OPTIONS
The following options are supported:
-i interface
Specify a WiFi Link interface to start the wpad daemon.
-k pre_shared_key_name
Specify the pre-shared key used for the WiFi Link.
EXAMPLES
Example 1 Starting the wpad Daemon on Specific WiFi Link
To create the WPA key psk, enter the following command:
# dladm create-secobj -c wpa psk
To use key psk to connect to ESSID wlan on link ath0, enter the following command:
# dladm connect-wifi -k psk -e wlan ath0
Example 2 Stopping the wpad Daemon on Specific WiFi Link
To stop the daemon on the link ath0, enter:
# dladm disconnect-wifi ath0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWwpau, SUNWwpar |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), dladm(1M), svcadm(1M), attributes(5), smf(5)
NOTES
The wpad service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/wpa:<link>
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.11 11 Mar 2008 wpad(1M)