I'm having this error when I do full fs cleanup
# fsck -F vxfs -o full /dev/vg01/lvol1
vxfs fsck: file system had I/O error(s) on meta-data.
log replay in progress
vxfs fsck: file system had I/O error(s) on meta-data.
vxfs fsck: file system had I/O error(s) on meta-data.
pass0 - checking... (2 Replies)
I am using raidctl on a v440 disk and noticed it resyncs after every boot, which takes about 30 minutes because of the size of the partition. I am concerned with what happens during the resync if "writes" happen to the disk before it is complete?
Any info would be helpful.
Thanks (0 Replies)
Hey peeps,
Here is somethin u might find interestin....
Is it possible to recover data from a partition which used to be an ext3 file sytem with some nice forgotten backups, which now is an lvm partion containg root partition of another OS. :)
I couldn't create any mess better than this, can... (2 Replies)
Hi All,
I am writing a block driver for a 2GB SD card where i get the total amount of data per request as follows:
struct request *req;
uint card_addr,total_bytes;
struct request_queue *rq = BlkDev->queue;
req = elv_next_request(rq);
..
..
card_addr = req->sector*512;... (1 Reply)
Hi,
could any one tell is there any test-suite or any idea How to do data corruption validation testing, means there is no any data corruption ?
Regards
Manish (1 Reply)
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
In my infinite lack of wisdom, I brought a Solaris 10(Sparc, 64 bit ) system down to init 1, detached a metadrive so that I could run format->analyze->refresh on it, and then reinit'd and reattached it .
It started syncing the drive as it's a submirror of a mirrored drive, which happens... (8 Replies)
/tmp/man18809436: Invalid file system control data detected
Help me
what do I do?
Если знаете русскии, пишите на нем. (2 Replies)
Discussion started by: islily
2 Replies
LEARN ABOUT HPUX
dircmp
dircmp(1) General Commands Manual dircmp(1)NAME
dircmp - directory comparison
SYNOPSIS
n] dir1 dir2
DESCRIPTION
examines dir1 and dir2 and generates various tabulated information about the contents of the directories. Sorted listings of files that
are unique to each directory are generated for all the options. If no option is entered, a sorted list is output indicating whether the
filenames common to both directories have the same contents.
Compare the contents of files with the same name in
both directories and output a list telling what must be changed in the two files to bring them into agreement. The list
format is described in diff(1).
Suppress messages about identical files.
Change the width of the output line to
n characters. The default width is 72.
EXTERNAL INFLUENCES
Environment Variables
LC_COLLATE determines the order in which the output is sorted.
If is not specified in the environment or is set to the empty string, the value of is used as a default. If is not specified or is set to
the empty string, a default of ``C'' (see lang(5)) is used instead of If any internationalization variable contains an invalid setting,
behaves as if all internationalization variables are set to ``C'' (see environ(5)).
International Code Set Support
Single- and multi-byte character code sets are supported.
EXAMPLES
Compare the two directories and and produce a list of changes that would make the directories identical:
WARNINGS
This command is likely to be withdrawn from X/Open standards. Applications using this command might not be portable to other vendors' sys-
tems. As an alternative is recommended.
SEE ALSO cmp(1), diff(1).
STANDARDS CONFORMANCE dircmp(1)