As you told we tried for each..
it shows error like..
but
i got this info by viewing : linuxquestions.org - questions - linux-software-2/why-cant-i-mount-this-md0-raid-mdadm-and-software-raid-345232/ Why can't I mount this md0 raid? (mdadm and software raid)
My only Need is :: To get all data in "sdb" to be accessible
No problem if it comes in one directory or different directory.
Last edited by Scott; 03-28-2011 at 12:14 PM..
Reason: Use code tags, please...
Hi...
question is this:
How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure.
... (4 Replies)
Hi,
I set up a RAID 5 configuration and for some reason the volumes won't mount when the system boots. I have to manually mount them from the command line and all is fine.
Here's the vfstab entries:
#device device mount FS fsck mount mount
#to mount ... (2 Replies)
I am having trouble mounting with cifs, but mounting the exact same command with smbfs works fine. The share is on another samba server and is set to full public guest access. # mount -t cifs //servername/sharename /mnt/temp -o password=""
mount error 13 = Permission denied Refer to the... (3 Replies)
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT FREEBSD
msdosfs
MSDOSFS(5) BSD File Formats Manual MSDOSFS(5)NAME
msdosfs -- MS-DOS file system
SYNOPSIS
options MSDOSFS
DESCRIPTION
The msdosfs driver will permit the FreeBSD kernel to read and write MS-DOS based file systems.
The most common usage follows:
mount -t msdosfs /dev/ada0sN /mnt
where N is the partition number and /mnt is a mount point. Some users tend to create a /dos directory for msdosfs mount points. This helps
to keep better track of the file system, and make it more easily accessible.
It is possible to define an entry in /etc/fstab that looks similar to:
/dev/ada0sN /dos msdosfs rw 0 0
This will mount an MS-DOS based partition at the /dos mount point during system boot. Using /mnt as a permanent mount point is not advised
as its intention has always been to be a temporary mount point for floppy and ZIP disks. See hier(7) for more information on FreeBSD direc-
tory layout.
SEE ALSO mount(2), unmount(2), mount(8), mount_msdosfs(8), umount(8)AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD October 1, 2013 BSD