03-26-2011
two gpfs in one node issue
dear all
can i create two gpfs in one node each gpfs is pointing to single hdiskpower
Last edited by thecobra151; 03-26-2011 at 11:48 AM..
Reason: more description
10 More Discussions You Might Find Interesting
1. AIX
Hi Administrators,
I have one issue related to GPFS filesystem. We have bad entries in this file system, which reflects error like
ls: 0653-341 The file <filename> does not exist.
when we give "ls -ltr" on this directory.
So we taken the FS filesystem offline and followed the below steps.
... (6 Replies)
Discussion started by: gauravgarg
6 Replies
2. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
3. AIX
Hi,
I have a running GPFS cluster. For one every mountpoint that i have created i have one disk assigned to it. That disk is converted to an NSD and is a part of the GPFS Cluster.
Now i have a new disk and there is this requirement to add it to the GPFS cluster, such that this becomes an NSD.... (1 Reply)
Discussion started by: aixromeo
1 Replies
4. AIX
Hello I am interested if anybody uses GPFS and is it must to have GPFS in the POWERHA environment?
and can GPFS work as cluster active active or active passive
thanks in advance (0 Replies)
Discussion started by: Vit0_Corleone
0 Replies
5. AIX
Dear all
for the last few days i was searching in IBM web site for GPFS 3.3 to upgrade my gpfs from 3.2 to 3.3 and i did not find the download link for the GPFS 3.3 in IBM website please can anyone give me the link . (4 Replies)
Discussion started by: thecobra151
4 Replies
6. AIX
Hi,
I have a running HACMP Cluster with two nodes. Its working in active/passive mode. (i.e Out of the two nodes in the cluster one will be active and the other one will be on standby. If first node fails the other takes over)
1. There is a Service IP associated with the cluster. Now the... (2 Replies)
Discussion started by: aixromeo
2 Replies
7. AIX
Hi,
I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS.
I have two LPARs on which GPFS is configured (4-5 disks)
Now these two LPARs need to be configured for HACMP (PowerHA) as well.
What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies
8. Homework & Coursework Questions
Hi Experts,
I am in need of running a script from one node say node 1 via node 2.
My scheduling tool dont have access to node2 , so i need to invoke the list file from node1 but the script needs to run from node2. because the server to which i am hitting, is having access only for the node... (5 Replies)
Discussion started by: arun1377
5 Replies
9. HP-UX
Hi,
We have HP UX service guard cluster on OS 11.23. Recently 40+ LUNs presented to both nodes by SAN team but I was asked to mount them on only one node. I created required VGs/LVs, created VxFS and mounted all of them and they are working fine. Now client requested those FS on 2nd node as... (4 Replies)
Discussion started by: prvnrk
4 Replies
10. IP Networking
I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool.
Nothing has changed on the LAN that... (2 Replies)
Discussion started by: SmokeyJoe
2 Replies
load(8) System Manager's Manual load(8)
Name
load - down-line load software to a target node
Syntax
/etc/load [ node ]
Description
The command loads software to an unattended target node. The target node is loaded by the host that executes the command.
The command requires the identification of the service circuit over which the load is performed, the Ethernet hardware address of the tar-
get node, and the service password needed to gain access to the target. This information is included in the nodes database entry for the
target node. A node entry is defined with the command. For further information, see The node is the name or address of the target node.
A node name consists of from one to six alphanumeric characters. For single networks, a node address consists of a decimal integer
(1-1023). For multiple networks, a node address consist of two decimal integers (n.n), where the first indicates the network number
(1-63), and the second indicates the node address (1-1023).
Options
-p Uses the specified service and password (next arguments) in accessing the target node. You can omit a target node's service and pass-
word from the nodes database for security reasons, but you must then specify the service and password in the command line by using the
option.
Examples
# /etc/load bangor -p 130fe
This command causes node to be loaded by the ULTRIX host node executing the command. The ULTRIX host uses the load files specified in the
nodes database entry for node to perform the load.
See Also
addnode(8), ccr(8), getnode(8), mop_mom(8), remnode(8), trigger(8)
Guide to Local Area Transport Servers
load(8)