Top header says 50% free, but table shows 100% used
Hi,
Can anyone explain this?
There are many more lines of top results, adding up to well over 100%. Due to decent performance, I'm assuming the values in the header section are correct, but why the discrepancy? It is a VPS, if that's relevant.
When I run the top command, it shows 1 process as being Stopped. This is not a zombie, but simply a stopped process. Unfortunately, I can't figure out how to tell which process this is, nor why it is in a stopped state? Any way of finding this out? (7 Replies)
Now, I had installed free bsd at my office. Unfortunitely, Email server have been using Local PoP3 and SMTP to our ISP with outlook. but my unix firewall sever ( free bsd ) didn't allow these port ( 110 & 25 ).
How can i create the IP table to pass at server. If u have any experience about obvious... (4 Replies)
Hi Gurus,
For a particular slice I have change the minfree from 10% to 1% with tunefs -m and its allowing the creation of file on that slice, however when I am seeing the same with df -k it says that the slice is 100% full.
What could be reason for this?
Thanks (2 Replies)
hi,
I want to extract and save the cpu(s) information from top command output, but individual cpu statistics separately on a multi-processor machine.
In command line, top will show this statistics when we press the switch "1".
any ideas?
thanks,
meharo (3 Replies)
Hi Export,
i execute 'top' command to show the free memory in Solaris host, but the read is much lower than the RSS value shown in prstat command. Which one can reflect the real status and it is possible the difference caused by any patch of OS?
Top command (only 883 memory is free)... (3 Replies)
I have a Script that generates 3 columns of the result. The line script is
/usr/xpg4/bin/awk -F' ' '{print $1 /t $2}' File_Name | awk -F'>' '{print $2}' | cut -d'<' -f1 | sort -rn | uniq -c
The output of the Command is :
Code.500 4 Input Error
Code.404 ... (4 Replies)
Hi,
When I run the free command on solaris, I get the following:
"Memory: 60G phys mem, 69G free mem"
Q: how cna the free mem be higher then the physical mem?:confused:
Amit (3 Replies)
I'm trying to take mrt output and put it at the top of a file along with the date and time. I was able to do it at the bottom of the file with the following
printf "********** $(date) **********\n\n" >> $OUTPUT_PATH/$HOSTNAME
mtr -r -w -c 10 $HOSTADDRESS >> $OUTPUT_PATH/$HOSTNAME
printf... (2 Replies)
Discussion started by: kramer65
2 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)