sunbox1 sunbox2 ---------- Post updated 03-16-11 at 01:52 AM ---------- Previous update was 03-15-11 at 11:40 PM ----------
My problem is resolved. First of all thanks to all who gave me kind support.
I am sorry. My NVram was not inserted.
After insert my NVram again i was again not able to see my MAC address. What i did, I added the below line in /etc/rc2 then i was able to see the MAC after running the command ifconfig -a
The line which i inserted under /etc/rc2
Last edited by Scott; 04-15-2011 at 02:10 PM..
Reason: Code tags, please...
Ok I a n00b, not gunna hide it so here goes -
Sun Solaris, V.10 i386 - during the setup, I can choose a screen resolution that looks great with 65k colors and all. However, when all is said and done 4 disks and a reboot later, I get hanious 640x480 @ 256 only.
If I choose the Sun Java Desktop... (20 Replies)
Hey there,
I am starting a Computer Science Foundation year at the end of this month and am trying to get a little bit ahead of the game. I have always wanted to learn Unix and am currently struggling with creating a boot disc to run Solaris (I have chosen to study this) from as opposed to... (0 Replies)
I am new to Sun.
I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor?
Thanks. (3 Replies)
Hello there!
I have Sun Fire 3800 with very old Solaris 9 and I need to perform upgrade to concurrent Solaris 10 version, preserving current OS configuration. I supose to make it using Live Upgrade, but according to Solaris Live Upgrade Software: Minimum Patch Requirements page, I need to... (5 Replies)
Hi,
i installed Sun Solaris 10 on VmWare Workstation 6.5 on my Windwos Vista PC. I would to ping solaris virtual machin froma my pc, but i can't do that. Can help me?!
I'm sorry for my bad English.
akela87 (2 Replies)
hi....
i have sun solaris 10 server, fedora 10, and Windows Server.. i cant ping my sun solaris 10, fedora 10 and Windows Server using hostname (etc: ping winserver.bengkel2.com), but i can ping all using IPV4 and IPV6 address.. can u give some suggestion to solve my problem or some idea to... (3 Replies)
Hi Gurus
I am not able to find the patching procedure for solaris 10 ( sol10 u11) to latest patchset with sun cluster having failover zones so that same I should follow.
Take an instance, there are sol1 and sol2 nodes and having two failover zones like sozone1-rg and sozone2-rg and currently... (1 Reply)
Discussion started by: nick101
1 Replies
LEARN ABOUT FREEBSD
if_gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD