03-14-2011
DNS configuration on AIX 6.1
Hello All,
I want to install ORACLE RAC on AIX 6.1.
In the installation guide. the below two points were mentioned:
Each node must have at least two network adapters or network interface cards
(NICs): one for the public network interface, and one for the private network
interface (the interconnect).
How can i check if i have two network adapters or network interface cards?
If i do not have how can i add ?
Before starting the installation, you must have at least two interfaces configured on
each node: One for the private IP address and one for the public IP address.
How can i do that ?
A DHCP service running on the public network for the cluster
How can i check if DHCP service is running ? in case not how can i run it ?
9 More Discussions You Might Find Interesting
1. IP Networking
Hi all,
I am a beginner in DNS service and I face difficult when configure DNS sub domain using "bind" version 8. So I would like to ask a question about this and hope someone can answer my question.
Is it possible to configure a sub domain in which the name of this sub domain is same as a... (2 Replies)
Discussion started by: raylai
2 Replies
2. IP Networking
i have the DNS and the web proxy services running on one of my sun machines....the funny thing is clients use the proxy server by addressing it with its IP address only....what i need is to assign it like...proxy.amu.edu.et......
my guess is the problem is the configuration with the DNS ...but i... (2 Replies)
Discussion started by: henokia4j
2 Replies
3. AIX
I'm trying to configure DNS on a AIX 5.4 machine and I just can't figure it out. The IBM guide doesn't work. Smit also doesn't work. I have no idea how to make this happen. (2 Replies)
Discussion started by: madavid0
2 Replies
4. UNIX for Dummies Questions & Answers
Hi All,
I have a list of few DNS server with hostnmae and IP which I need to setup in Solaris Servers...Can any one pls tell me the steps for setting up the above in solaris 10 & 9???? (4 Replies)
Discussion started by: solaris5.10
4 Replies
5. Red Hat
Dear All I want to configure DNS in redhat linux. i am following these steps but when i restart the services it is showing status failed. Please any body can help me on urgent basis.
#service named restart
Stopping named:
Starting named:
---------Edited in named.conf... (2 Replies)
Discussion started by: sahu.tapan
2 Replies
6. UNIX for Dummies Questions & Answers
Hi to all.
Sorry for my bad english.
For pure self-educational, not professional, purposes, I am studying how to configure a server with several services operating on it.
For my experiment I'm using VirtualBox 3.1.4 on a WinXP host with 3 FreeBSD guests; one acts as a DHCP + DNS server; the... (0 Replies)
Discussion started by: marboxer
0 Replies
7. UNIX for Dummies Questions & Answers
Hello fellow unix dudes, I have a question on DNS.
Basically the error is my domain.com server can not send email to my
mail.domain.com server.
I have a virtual server with one IP say 192.10.11.12 and a mail server with
iP 172.4.5.6
When the virutal server on ip 192.10.11.12 was setup,... (0 Replies)
Discussion started by: photon
0 Replies
8. Red Hat
I wanted to know how to configure DNS configuration for RHEL 5.
I hope, my query is clear of how to setup DNS for RHEL 5.
Please revert with the reply to my query
Regards (6 Replies)
Discussion started by: RHCE
6 Replies
9. Shell Programming and Scripting
Hello to all,
May someone help me with this DNS configuration issue please.
I have configured wildcard to different IPs like below and it works.
xyz IN SOA dns.abcd. . (
2014120901
10800
3600
604800
... (0 Replies)
Discussion started by: Ophiuchus
0 Replies
ris(8) System Manager's Manual ris(8)
Name
ris - remote installation services utility
Syntax
/etc/ris
Description
The utility performs remote installation services which install system software to a client machine through the TCP/IP local network. The
client machine can be a VAX or a RISC machine.
The server on which the remote installation services area is located can be either a VAX or a RISC machine.
The remote installation services utility uses the directory as a base. When you install the first product to the utility creates a remote
installation services area. The area is called either or
The area contains one or more ULTRIX software products. Each product contains the subsets of the kits that can be installed to clients on
a network. Clients registered for an area install software over the network to their processor.
The utility performs the following functions:
a - Add client
r - Remove client
s - Show products in remote installation environments
m - Modify client
i - Install software
You must use the utility interactively to set up a remote installation services area. After you have set up a remote installation services
area on the server, you can use the utility either interactively or from the command line to manage clients.
The directory also holds a subdirectory, This directory contains a database file, that you can use to manage multiple clients.
Examples
The example that follows invokes the utility interactively:
# /etc/ris
A menu appears from which you can select options to perform functions.
The examples that follow manage the client using the command line.
The syntax of the command to add a client follows:
/etc/ris -a <clientname> -h <Ethernet_address> -p path,product[,product]
The following command adds client and allows that client to install a product over the network:
# /etc/ris -a bergal -h 08-00-2B-03-05-8B -p ris0.mips,product_1
The syntax of the command to modify a client follows:
/etc/ris -a <clientname> [-h <Ethernet_address>] [-p <path,product,product>]
The following command modifies client and allows that client to install a product over the network:
# /etc/ris -m bergal -p ris0.mips,product_2
The syntax of the command to remove a client follows:
/etc/ris -r <clientname>
The following command removes client
# /etc/ris -r bergal
Files
See Also
setld(8)
Guide to the Remote Installation Services
Guide to Server Setup
ris(8)