03-10-2011
"plumbed" is a solaris thing, I can't say. ifconfig -a suffices to include interfaces that aren't "up" in Linux but -a seems to have a slightly different meaning in Solaris.
Since your question is hardware and OS specific you might have more luck asking in unix.com's Solaris section.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
3. Solaris
Hi Community,
I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output:
# ifconfig hme0 <ip_address> netmask <mask> plumb
#ifconfig: plumb: hme0: no such interface
I've the same thing with dhcp service.
could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies
4. IP Networking
Hi,
ifconfig -a return:
eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A
inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0
... (5 Replies)
Discussion started by: djbuly
5 Replies
5. UNIX for Advanced & Expert Users
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
8. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT HPUX
suninstall
suninstall(1M) System Administration Commands suninstall(1M)
NAME
suninstall - install the Solaris operating system
SYNOPSIS
suninstall
DESCRIPTION
install-solaris(1M) is now the preferred command for starting and restarting the Solaris Installation program. It should be used instead of
suninstall. suninstall is symbolically linked to install-solaris.
suninstall is a forms-based and graphical subsystem for installing the operating system.
suninstall exists only on the Solaris installation media (CD or DVD) and should only be invoked from there. Refer to the Solaris 10 Instal-
lation Guide: Basic Installations for more details.
suninstall allows installation of the operating system onto any standalone system. suninstall loads the software available on the installa-
tion media. Refer to the Solaris 10 Installation Guide: Basic Installations for disk space requirements.
USAGE
Refer to the Solaris 10 Installation Guide: Basic Installations for more information on the various menus and selections.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
SEE ALSO
pkginfo(1), install(1M), install-solaris(1M), pkgadd(1M), attributes(5)
Solaris 10 Installation Guide: Basic Installations
NOTES
It is advisable to exit suninstall by means of the exit options in the suninstall menus.
SunOS 5.10 9 Sep 2004 suninstall(1M)