03-05-2011
Since i was unable to find a way to get the disk recognized using UFS i went with ZFS and was able to see all of the disk and created an /nfs and /oracle partition with no problem.
10 More Discussions You Might Find Interesting
1. Solaris
All,
Is there a way to RAID the disks in Solaris 9? Solaris 8 provided DiskSuite for mirroring disk drives. Is there a GUI for DiskSuite in Solaris 9?
Thanks,
Mike (2 Replies)
Discussion started by: bubba112557
2 Replies
2. Solaris
whats the command to find name of all disks. Is it iostat -En ? (1 Reply)
Discussion started by: vikashtulsiyan
1 Replies
3. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
4. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
5. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
6. Solaris
Hello,
I've read many posts that offer tips on how to mount a CDROM but I haven't seen any on how to get the system to recognize the CDROM drive.
I was transferring files from CDROM to the hard drive successfully. I entered the third CDROM and the system refused to automount it. I tried... (2 Replies)
Discussion started by: TrueSon
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
10. Solaris
Hello,
I got into a wired state on one of solaris 10 server. When I noticed that server is having some issue, I found that there were dumpadm.conf entries in /etc/shadow and real entries were wiped of. Probably somebody fat fingers.
I was able to boot into failsafe, break SVM mirror, copied... (25 Replies)
Discussion started by: solaris_1977
25 Replies
LEARN ABOUT ULTRIX
disktab
disktab(5) File Formats Manual disktab(5)
Name
disktab - disk description file
Syntax
#include <disktab.h>
Description
The file is a simple data base that describes disk geometries and disk partition characteristics. The format is patterned after the termi-
nal data base. Entries in consist of a number of fields separated by colons (:). The first entry for each disk gives the names that are
known for the disk, separated by vertical bars (|). The last name given should be a long name fully identifying the disk.
The following list indicates the normal values stored for each disk entry:
Name Type Description
ns num Number of sectors per track
nt num Number of tracks per cylinder
nc num Total number of cylinders on the disk
ba num Block size for partition `a' (bytes)
bd num Block size for partition `d' (bytes)
be num Block size for partition `e' (bytes)
bf num Block size for partition `f' (bytes)
bg num Block size for partition `g' (bytes)
bh num Block size for partition `h' (bytes)
fa num Fragment size for partition `a' (bytes)
fd num Fragment size for partition `d' (bytes)
fe num Fragment size for partition `e' (bytes)
ff num Fragment size for partition `f' (bytes)
fg num Fragment size for partition `g' (bytes)
fh num Fragment size for partition `h' (bytes)
pa num Size of partition `a' in sectors
pb num Size of partition `b' in sectors
pc num Size of partition `c' in sectors
pd num Size of partition `d' in sectors
pe num Size of partition `e' in sectors
pf num Size of partition `f' in sectors
pg num Size of partition `g' in sectors
ph num Size of partition `h' in sectors
se num Sector size in bytes
ty str Type of disk (e.g. removable, winchester)
The entries can be automatically generated with the program.
Files
See Also
chpt(8), newfs(8)
disktab(5)