03-04-2011
Quote:
Originally Posted by
Celtic_Monkey
when you say you cant see the raid 5 drives, how are you checking?
what says # format < /dev/null
have you tried a reconfiguration boot?
the format command just shows the two drives in my RAID1 config. I've tried touch /reconfigure and rebooting the system and the drives still were not available.
10 More Discussions You Might Find Interesting
1. Solaris
All,
Is there a way to RAID the disks in Solaris 9? Solaris 8 provided DiskSuite for mirroring disk drives. Is there a GUI for DiskSuite in Solaris 9?
Thanks,
Mike (2 Replies)
Discussion started by: bubba112557
2 Replies
2. Solaris
whats the command to find name of all disks. Is it iostat -En ? (1 Reply)
Discussion started by: vikashtulsiyan
1 Replies
3. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
4. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
5. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
6. Solaris
Hello,
I've read many posts that offer tips on how to mount a CDROM but I haven't seen any on how to get the system to recognize the CDROM drive.
I was transferring files from CDROM to the hard drive successfully. I entered the third CDROM and the system refused to automount it. I tried... (2 Replies)
Discussion started by: TrueSon
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
10. Solaris
Hello,
I got into a wired state on one of solaris 10 server. When I noticed that server is having some issue, I found that there were dumpadm.conf entries in /etc/shadow and real entries were wiped of. Probably somebody fat fingers.
I was able to boot into failsafe, break SVM mirror, copied... (25 Replies)
Discussion started by: solaris_1977
25 Replies
VMSTAT(1) General Commands Manual VMSTAT(1)
NAME
vmstat - report virtual memory statistics
SYNOPSIS
vmstat [ -fsi ] [ drives ] [ interval [ count ] ]
DESCRIPTION
Vmstat delves into the system and normally reports certain statistics kept about process, virtual memory, disk, trap and cpu activity. If
given a -f argument, it instead reports on the number of forks and vforks since system startup and the number of pages of virtual memory
involved in each kind of fork. If given a -s argument, it instead prints the contents of the sum structure, giving the total number of
several kinds of paging related events which have occurred since boot. If given a -i argument, it instead reports on the number of inter-
rupts taken by each device since system startup.
If none of these options are given, vmstat will report in the first line a summary of the virtual memory activity since the system has been
booted. If interval is specified, then successive lines are summaries over the last interval seconds. ``vmstat 5'' will print what the
system is doing every five seconds; this is a good choice of printing interval since this is how often some of the statistics are sampled
in the system; others vary every second, running the output for a while will make it apparent which are recomputed every second. If a
count is given, the statistics are repeated count times. The format fields are:
Procs: information about numbers of processes in various states.
r in run queue
b blocked for resources (i/o, paging, etc.)
w runnable or short sleeper (< 20 secs) but swapped
Memory: information about the usage of virtual and real memory. Virtual pages are considered active if they belong to processes which are
running or have run in the last 20 seconds. A ``page'' here is 1024 bytes.
avm active virtual pages
fre size of the free list
Page: information about page faults and paging activity. These are averaged each five seconds, and given in units per second.
re page reclaims (simulating reference bits)
at pages attached (found in free list)
pi pages paged in
po pages paged out
fr pages freed per second
de anticipated short term memory shortfall
sr pages scanned by clock algorithm, per-second
up/hp/rk/ra: Disk operations per second (this field is system dependent). Typically paging will be split across several of the available
drives. The number under each of these is the unit number.
Faults: trap/interrupt rate averages per second over last 5 seconds.
in (non clock) device interrupts per second
sy system calls per second
cs cpu context switch rate (switches/sec)
Cpu: breakdown of percentage usage of CPU time
us user time for normal and low priority processes
sy system time
id cpu idle
If more than 4 disk drives are configured in the system, vmstat displays only the first 4 drives, with priority given to Massbus disk
drives (i.e. if both Unibus and Massbus drives are present and the total number of drives exceeds 4, then some number of Unibus drives will
not be displayed in favor of the Massbus drives). To force vmstat to display specific drives, their names may be supplied on the command
line.
FILES
/dev/kmem, /vmunix
SEE ALSO
systat(1), iostat(1)
The sections starting with ``Interpreting system activity'' in Installing and Operating 4.2bsd.
4th Berkeley Distribution March 15, 1986 VMSTAT(1)