03-04-2011
Solaris not recognizing RAID 5 disks
I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and have also tried to add the disk using SMC but am having no luck at all. Does anyone have any idea how i can get these disks to be visible to the OS?
10 More Discussions You Might Find Interesting
1. Solaris
All,
Is there a way to RAID the disks in Solaris 9? Solaris 8 provided DiskSuite for mirroring disk drives. Is there a GUI for DiskSuite in Solaris 9?
Thanks,
Mike (2 Replies)
Discussion started by: bubba112557
2 Replies
2. Solaris
whats the command to find name of all disks. Is it iostat -En ? (1 Reply)
Discussion started by: vikashtulsiyan
1 Replies
3. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
4. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
5. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
6. Solaris
Hello,
I've read many posts that offer tips on how to mount a CDROM but I haven't seen any on how to get the system to recognize the CDROM drive.
I was transferring files from CDROM to the hard drive successfully. I entered the third CDROM and the system refused to automount it. I tried... (2 Replies)
Discussion started by: TrueSon
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
10. Solaris
Hello,
I got into a wired state on one of solaris 10 server. When I noticed that server is having some issue, I found that there were dumpadm.conf entries in /etc/shadow and real entries were wiped of. Probably somebody fat fingers.
I was able to boot into failsafe, break SVM mirror, copied... (25 Replies)
Discussion started by: solaris_1977
25 Replies
AAC(4) BSD Kernel Interfaces Manual AAC(4)
NAME
aac -- Adaptec AdvancedRAID Controller driver
SYNOPSIS
aac* at pci? dev ? function ?
ld* at aac? unit ?
DESCRIPTION
The aac driver provides support for the Adaptec AAC family of SCSI and SATA RAID controllers. These controllers support RAID 0, 1, 5, 10,
and volume sets. They have four channels in the add-in version or 1-2 channels in the motherboard integrated version, and are most often
found rebadged by Dell, Hewlett-Packard or IBM. Supported controllers include:
o Adaptec AAC-364
o Adaptec SCSI RAID 2120S
o Adaptec SCSI RAID 2200S
o Adaptec SATA RAID 2410SA
o Adaptec SATA RAID 3405
o Adaptec SCSI RAID 5400S
o Dell PERC 2/Si
o Dell PERC 2/QC
o Dell PERC 3/Di
o Dell PERC 3/Si
o Dell PERC 320/DC
o Dell CERC SATA RAID 1.5/6ch
o HP NetRAID 4M
o HP ML110 G2 (Adaptec SATA RAID 2610SA)
o IBM ServeRAID 8k
Access to RAID containers is available via the ld device driver. Individual drives cannot be accessed unless they are part of a container or
volume set, and non-fixed disks cannot be accessed. Containers can be configured by using the on-board BIOS utility of the card.
DIAGNOSTICS
The adapter can send status and alert messages asynchronously to the driver. These messages are printed on the system console.
SEE ALSO
intro(4), ld(4)
HISTORY
The aac driver first appeared in NetBSD 1.6, and was based on the FreeBSD driver of the same name.
BUGS
This driver is not compatible with controllers that have version 1.x firmware. The firmware version is the same as the kernel version
printed in the BIOS POST and driver attach messages.
BSD
February 19, 2011 BSD