02-27-2011
A packet sniffer likes tcpdump or wireshark is quite handy in such situations.
9 More Discussions You Might Find Interesting
1. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
2. Linux
Hi,
For some reason my network card started going 10Mb/s half duplex instead of 1000Mb/s full duplex. System is connected to 8x1Gb HP switch.
Other devices connect fine through the switch and get full 1Gb network.
I have Centos 5 with all updates. Driver comes from elrepo and as well is... (1 Reply)
Discussion started by: columb
1 Replies
3. Programming
I am trying to make a server and client, the client will choose between some options and the server will react accordingly.
After a some reads and writes that work the server needs to read from client an INT i use this:
read(newSd,&k,sizeof(int));But even if all the other times there was no... (1 Reply)
Discussion started by: theSling
1 Replies
4. AIX
I have configured a custom application monitor with restart count = 3.
say the application has restarted 2 times, if the application fail 2 more times within restart interval, it will failover.
Is there any counter to tell me the recent restart count?
Thanks!! (1 Reply)
Discussion started by: skeyeung
1 Replies
5. Red Hat
I was testing Networking Teaming (activebackup) with a VM hosted on VmWare Workstation and VirtualBox, and the result is, if the active interface is down, the system is not using the backup interface.
Tested on both CentOS / RHEL 7
Please find below the command I have used to configure teaming.... (0 Replies)
Discussion started by: atanubanerji
0 Replies
6. Web Development
Hi All,
Frankly I'm new to Linux Environment. While we are trying to Host an ASP.NET 5 Web Application on Centos OS7 Web hosting Server. There were couple of steps which we are supposed to go through, please see this link -
We are stuck at Create a Container & then Running the Container,... (1 Reply)
Discussion started by: John Fredric
1 Replies
7. Emergency UNIX and Linux Support
Hi all,
I need to add domain and search parameters to resolv.conf, however network manager overwrites.
Setting the PEERDNS=No in the interface file seems to have no effect on this behaviour.
Sadly I cannot just disable NM as these are not my hosts, I'm just attempting to install a platform... (3 Replies)
Discussion started by: Skrynesaver
3 Replies
8. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
9. Infrastructure Monitoring
After setting up MQTT and testing some ESP8266 and ESP32 modules, where I noted that testing in Programming ESP32 (ESP-WROOM-32) as an MQTT Client Subscribed to Linux Server Load Average Messages, I was so impressed with MQTT that I installed MQTT on three different computers, instantly and... (2 Replies)
Discussion started by: Neo
2 Replies
LEARN ABOUT NETBSD
ipresend
IPRESEND(1) General Commands Manual IPRESEND(1)
NAME
ipresend - resend IP packets out to network
SYNOPSIS
ipresend [ -EHPRSTX ] [ -d <device> ] [ -g <gateway> ] [ -m <MTU> ] [ -r <filename> ]
DESCRIPTION
ipresend was designed to allow packets to be resent, once captured, back out onto the network for use in testing. ipresend supports a num-
ber of different file formats as input, including saved snoop/tcpdump binary data.
OPTIONS
-d <interface>
Set the interface name to be the name supplied. This is useful with the -P, -S, -T and -E options, where it is not otherwise possi-
ble to associate a packet with an interface. Normal "text packets" can override this setting.
-g <gateway>
Specify the hostname of the gateway through which to route packets. This is required whenever the destination host isn't directly
attached to the same network as the host from which you're sending.
-m <MTU>
Specify the MTU to be used when sending out packets. This option allows you to set a fake MTU, allowing the simulation of network
interfaces with small MTU's without setting them so.
-r <filename>
Specify the filename from which to take input. Default is stdin.
-E The input file is to be text output from etherfind. The text formats which are currently supported are those which result from the
following etherfind option combinations:
etherfind -n
etherfind -n -t
-H The input file is to be hex digits, representing the binary makeup of the packet. No length correction is made, if an incorrect
length is put in the IP header.
-P The input file specified by -i is a binary file produced using libpcap (i.e., tcpdump version 3). Packets are read from this file
as being input (for rule purposes).
-R When sending packets out, send them out "raw" (the way they came in). The only real significance here is that it will expect the
link layer (i.e. ethernet) headers to be prepended to the IP packet being output.
-S The input file is to be in "snoop" format (see RFC 1761). Packets are read from this file and used as input from any interface.
This is perhaps the most useful input type, currently.
-T The input file is to be text output from tcpdump. The text formats which are currently supported are those which result from the
following tcpdump option combinations:
tcpdump -n
tcpdump -nq
tcpdump -nqt
tcpdump -nqtt
tcpdump -nqte
-X The input file is composed of text descriptions of IP packets.
SEE ALSO
ipftest(1), ipsend(1), iptest(1), bpf(4), ipsend(5), tcpdump(8)
DIAGNOSTICS
Needs to be run as root.
BUGS
Not all of the input formats are sufficiently capable of introducing a wide enough variety of packets for them to be all useful in testing.
If you find any, please send email to me at darrenr@pobox.com
IPRESEND(1)