How to enable hba port of a two port hba card Post: 302498482

10 More Discussions You Might Find Interesting

1. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to...

2. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed....

3. IP Networking

4GB Dual Port HBA

I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB? Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks.

4. Solaris

Solaris 10. fcinfo hba-port shows adapter not Found

I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install? Thanks in advance....

5. Solaris

Few things related to HBA port & fcinfo command

Hi Gurus I need to know few things related to HBA port & fcinfo command I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above...

6. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

7. Solaris

Which FC HBA card support Solaris9

I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage. in OK prompt, PROBE-SCSI-ALL showing A5000 fc hdds details in ok prompt..... but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000...

8. Red Hat

HBA card faulty

Hi, How to determine if HBA card in getting faulty from linux host ? any pointers.

9. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;...

10. Solaris

Solaris 10: how to disable an unused HBA card

Dear all, I have a new Oracle Blade X4-2B server, running Solaris 10. The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing. My question is: how to disable this HBA card, without removing it physically...

LEARN ABOUT DEBIAN

ql-hba-snapshot

ql-hba-snapshot(8)					       System Administration						ql-hba-snapshot(8)

NAME

       ql-hba-snapshot - display specific information of the QLogic HBA.

SYNOPSIS

       ql-hba-snapshot <Host number> [OPTIONS]

DESCRIPTION

       FC HBA Snapshot Utility

       This  utility  displays	the  details  of  the QLogic HBA attached to the system. It uses one of the two file systems for scanning: proc or
       sysfs.

       <Host number> | <-a/--all> [optional]

	      Provide the <HOST NUMBER> to display the detailed information of the HBA.  With no option  specified,  general  information  of  all
	      hosts  will  be  displayed.   Ex.  # /usr/sbin/ql-hba-snapshot <Host Number> # /usr/sbin/ql-hba-snapshot --procfs <Host Number> (For
	      procfs)

       -h, --help

	      Prints the help message.	Ex.  # /usr/sbin/ql-hba-snapshot --help

       -hl, --hostlist

	      This option displays the list of QLogic hosts (HBAs) connected to this system.  The <HOST NUMBER> can be obtained by using following
	      command Ex.  # /usr/sbin/ql-hba-snapshot --hostlist

       -p, --parameters

	      This  option  displays  the  command  line parameters that can be passed to the QLogic HBA driver.  Ex.  # /usr/sbin/ql-hba-snapshot
	      --parameters <Host Number>

       -s, --statistics

	      This option displays the statistical information for specified host. Stastics option is only supported in "sysfs" based  scan.   Ex.
	      # /usr/sbin/ql-hba-snapshot --statistics <Host number/--all>

       -proc, --procfs

	      This options forces the the utility to scans information based on "procfs", instead of default sysfs.  Ex.  # /usr/sbin/ql-hba-snap-
	      shot --procfs [Other valid option]

       -v, --verbose

	      This enables verbose display. The detailed information of LUNs will be displayed in addition to standard one.  This option  is  only
	      supported in sysfs.  Ex.	# /usr/sbin/ql-hba-snapshot --verbose <Host number/-a>

SEE ALSO

       ql-dynamic-tgt-lun-disc(8), ql-lun-state-online(8), ql-set-cmd-timeout(8)

Matthias Schmitz <;matthias@sigxcpu.org> 			     July 2009							ql-hba-snapshot(8)

10 More Discussions You Might Find Interesting

1. Solaris

HBA Card

Discussion started by: xiaochensg

2. AIX

Need HBA card driver

Discussion started by: b_manu78

3. IP Networking

4GB Dual Port HBA

Discussion started by: jwholey

4. Solaris

Solaris 10. fcinfo hba-port shows adapter not Found

Discussion started by: Y4Net