Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Hi Gurus
I need to know few things related to HBA port & fcinfo command
I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT REDHAT
sndconfig
sndconfig(8) System Manager's Manual sndconfig(8)NAME
sndconfig - configure sound card for use with Linux kernel modules
SYNOPSIS
sndconfig {--help,--noprobe,--noautoconfig}
DESCRIPTION
sndconfig sets up the necessary configuration files to use a sound card on a Red Hat system. If PnP support is compiled in, by default snd-
config will do an initial probe for PnP sound cards using the pnpdump utility. If the --noprobe option is given this step will be skipped.
The user will be notified if any cards were found. Otherwise the user must pick the card type from a menu. Then the user must choose the
I/O port, IRQ, and DMA settings for the sound card. These must be known ahead of time and depend upon the jumper settings of the sound
card. For PnP cards, the program will determine settings for the card; if the --noautoconfig option is given the user can choose the val-
ues which will be programmed into the PnP device. There is no guarantee that the values entered do not conflict with an existing non-PnP or
PnP device. The user must make sure these types of conflicts do not occur.
OPTIONS
--help Print a usage message on standard output and exit successfully.
--noprobe
No probe will be made for PnP cards, and the PnP configuration files will not be changed.
--noautoconfig
No autoconfiguration of PnP cards will be done; the user will be prompted for settings.
FILES
/etc/sysconfig/soundcard Stores current settings /etc/modules.conf Stores sound module configuration /etc/isapnp.conf Stores
PnP configuration
SEE ALSO isapnp(1), pnpdump(1)
Wed Aug 19 1998 sndconfig(8)