How do I find if a server contains a DDS3 or a DDS2 drive remotely ?
I checked in SMIT and I noticed the description field according to tape drives, but is there another more thorough way?
Thanks,
Luke (0 Replies)
Hi,
Can you please help me to locate tape drives on Sun Server and the capacity of the tape drive.
I am managing a Sun 4u server.
Need this urgently.
Regards,
Vivek (2 Replies)
Hello,
I have a little problem with backup & restoring files from tape drive.
I am adding 3 directories to my tape, and it is OK:
hades# tar -cvf /dev/nsa0 test test1 restore
a test
a test/level1
a test/myharddisk.img
a test1
a test1/level1
a test1/myharddisk.img
a test1/test.img
a... (1 Reply)
We have a new i500 and have 4 TLO4 drives which are connected directly to 2 FC cards on the host. The host can communicate with the autochanger through whichever drive that is set as control path.
When I run inquire, all 4 drives are listed but auto changer doesn't show up. Does anyone know... (1 Reply)
Hi,
I am a abit new in AIX system administration field. I want to gather knowledge about backup techniques. As per my knowledge we use Tape archives for taking backups. Can anyone pls explain me in detail abt tape archive? Whether these tape archives come along with the systems or we have to... (1 Reply)
I have a server/domain on a m5000 running Solaris 10. It is part of a cluster.
The other cluster member sees tape drives, but this one does not.
It is zoned correctly, and I can see the drives are binded in lputil.
The st.conf, and devlink.tab are identical.
ST.CONF: -
#
# Copyright... (1 Reply)
Hi,
I have a machine, and mpzio fails everytime i reboot the server. The machine has tape drives and SAN storage, I'm not sure if that is my issue or not. I was told to not enable mpxio globally as that would do something bad to the tape drives. So, I set it to only make the two SAN connected... (4 Replies)
Good day!
Need help in checking my AIX 7.1 box.
After we have finished zoning our TS3200 and TS3310 tape libraries, we installed the Atape driver,
# lslpp -L |grep tape
Atape.driver 11.7.7.0 C F IBM AIX Enhanced Tape and
devices.fcp.tape.rte 7.1.3.15 C ... (0 Replies)
Discussion started by: alainken3
0 Replies
LEARN ABOUT ULTRIX
tms
tms(4) Kernel Interfaces Manual tms(4)Name
tms - TMSCP magnetic tape interface
Syntax
For UNIBUS, Q-bus:
controller klesiu0 at uba0
controller uq0 at klesiu0 csr 0174500 vector uqintr
tape tms0 at uq0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 3
For VAXBI:
controller klesib0 at vaxbi0 node 0
controller uq0 at klesib0 vector uqintr
tape tms0 at uq0 drive 0
controller aie0 at vaxbi? node?
controller bvpssp0 at aie0 vector bvpsspintr
tape tms0 at bvpssp0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 0
For VAX CI/HSC:
adapter ci0 at nexus?
adapter ci0 at vaxbi? node?
controller hsc0 at ci0 cinode 6
tape tms0 at hsc0 drive 3
Description
Prior to Version 2.0, this device was referenced by tmscp(4).
The TMSCP driver provides a standard tape drive interface, as described in This is a driver for any controller that adheres to the Tape
Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed the Tape
Mass Storage Control Protocol. This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape
drives). See for further details.
Tape Support
TK50, TK70, TF70, TU81, TU81e, TA78, TA79, TA81, RV20, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
FilesSee Alsomtio(4), nbuf(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tms(4)