02-18-2011
How to enable hba port of a two port hba card
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
3. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
4. Solaris
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Discussion started by: Y4Net
23 Replies
5. Solaris
Hi Gurus
I need to know few things related to HBA port & fcinfo command
I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Discussion started by: girish.batra
6 Replies
6. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
7. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
8. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Solaris
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT CENTOS
ibv_uc_pingpong
IBV_UC_PINGPONG(1) USER COMMANDS IBV_UC_PINGPONG(1)
NAME
ibv_uc_pingpong - simple InfiniBand UC transport test
SYNOPSIS
ibv_uc_pingpong [-p port] [-d device] [-i ib port] [-s size] [-r rx depth] [-n iters] [-l sl] [-e] HOSTNAME
ibv_uc_pingpong [-p port] [-d device] [-i ib port] [-s size] [-r rx depth] [-n iters] [-l sl] [-e]
DESCRIPTION
Run a simple ping-pong test over InfiniBand via the reliable connected (RC) transport.
OPTIONS
-p, --port=PORT
use TCP port PORT for initial synchronization (default 18515)
-d, --ib-dev=DEVICE
use IB device DEVICE (default first device found)
-i, --ib-port=PORT
use IB port PORT (default port 1)
-s, --size=SIZE
ping-pong messages of size SIZE (default 4096)
-r, --rx-depth=DEPTH
post DEPTH receives at a time (default 1000)
-n, --iters=ITERS
perform ITERS message exchanges (default 1000)
-l, --sl=SL
use SL as the service level value of the QP (default 0)
-e, --events
sleep while waiting for work completion events (default is to poll for completions)
SEE ALSO
ibv_rc_pingpong(1), ibv_ud_pingpong(1), ibv_srq_pingpong(1)
AUTHORS
Roland Dreier
<rolandd@cisco.com>
BUGS
The network synchronization between client and server instances is weak, and does not prevent incompatible options from being used on the
two instances. The method used for retrieving work completions is not strictly correct, and race conditions may cause failures on some
systems.
libibverbs August 30, 2005 IBV_UC_PINGPONG(1)