How to connect a 4TB G-Raid hard drive to a laptop? Post: 302496410

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Trying to copy old hard drive to new hard drive.

:confused: ........I have a new hard drive and I need to copy ALL info from the old to the new. I would like to use the dd command. I know the command is as follows...... dd if=/dev/rdsk/c1t1d0s0 of=/dev/rdsk/???????? Where I have the question marks is the problem. How do I find out what the...

2. Filesystems, Disks and Memory

The best partitioning schem for a 250GB Sata hard drive & a 75GB SCSI hard drive

Hi I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /...

3. UNIX for Dummies Questions & Answers

How to connect laptop to Unix system via Parallel port

Hi, I have been using a computer to keep track of inventory for my business. I am pretty sure it runs on Unix. In the back of the computer there is some sort of PCI card that has about 8 RJ-11 ports on it. I use that card to connect the Unix system to my 3 VT-220 terminals. I use a simple 6...

4. Slackware

installing slackware 10.2 on compaq laptop with Sansung HM121HI hard drive

Hi Guys, I'm trying to install slackware 10.2 on a on compaq laptop with Sansung HM121HI hard drive but I wonder what kernel should I use so it can recognize the had disk. Initially I've tried using sata.i and then try to use the fdisk utility to create the new partiotions but doesn't seem...

5. Solaris

Connect an External SCSI Hard Drive to Ultra 80

Guys, I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem. I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80. I connected it powered it up and at OK prompt did : boot -r system comes up and complains about not...

6. UNIX for Dummies Questions & Answers

RAID Drive

Hello, I have a machine that has software based RAID. One of the hard drives failed. The problem is that the old systems administrator created LVM and then RAID. My understanding is that RAID had to be created before and then the LVM's. Is there someway to install the new drive without loosing...

7. Ubuntu

Connect 2 laptops with RJ45 cable (Ubuntu 10.10 laptop with Windows 7 laptop)

Hi to all, I have the problem that a laptops with windows XP cannot startup even in safe mode nor using last good known configuration. I have a Ubuntu 10.10 Live CD and booting from it I can read the Hard Drive. I need to do a backup the Hard Drive from XP laptop and I want to connect this...

8. Solaris

Connect from Dell Laptop to SunBlade 100

Hi All I connect to my SunBlade using the keyboard/mouse provided by the sun. Now I would like to connect to it using my dell laptop running on Windows 7. I have connected the laptop to the SunBlade using just a one crossover 9-pin connector using the free/basic version of the terminal...

9. AIX

RAID 10 Failed Drive Swap

I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can...

LEARN ABOUT NETBSD

mlxctl

MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME

     mlxctl -- Mylex DAC960 family management utility

SYNOPSIS

     mlxctl [-f dev] [-v] [-a] status [drive] [...]
     mlxctl [-f dev] [-a] detach [drive] [...]
     mlxctl [-f dev] [-a] check [drive] [...]
     mlxctl [-f dev] rebuild channel:target
     mlxctl [-f dev] cstatus
     mlxctl [-f dev] rescan
     mlxctl [-f dev] config

DESCRIPTION

     The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.

     The following options are available:

     -a       Apply the action to all drives attached to the controller.

     -f dev   Specify the control device to use.  The default is /dev/mlx0.

     -v       Increased verbosity.

     The following commands are available:

     cstatus  Display the controller's current status.

     status   Display the status of the specified drives.  This command returns 0 if all drives tested are online, 1 if one or more drives are
	      critical and 2 if one or more are offline.

     rescan   Re-scan the logical drive table, and attach or detach devices from the system as necessary.

     detach   Detach the specified drives.  Drives must be unmounted and unopened for this command to succeed.

     check    Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5).	This command returns imme-
	      diately.	The status command can be used to monitor the progress of the check.

     rebuild  Rebuild onto the specified physical drive.  Note that there can be only one running rebuild operation per controller at any given
	      time.  This command returns immediately.	The cstatus command can be used to monitor the progress of the rebuild.

     config   Write the current system drive configuration to stdout.

EXAMPLES

     Display the status of drive ld3 attached to the controller mlx1:

	   mlxctl -f /dev/mlx1 -v status ld3

SEE ALSO

     ld(4), mlx(4)

HISTORY

     The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.

BUGS

     Modifying drive configuration is not yet supported.

     Some commands do not work with older firmware revisions.

     Error log extraction is not yet supported.

BSD
								  April 10, 2000							       BSD