02-14-2011
Its new and I can only connect it to the laptop or desktop though USB and that doesn't work at all. I am wondering if I need to connect it some how with the FW800 or eSATA cable and see if that will work.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
:confused: ........I have a new hard drive and I need to copy ALL info from the old to the new. I would like to use the dd command. I know the command is as follows......
dd if=/dev/rdsk/c1t1d0s0 of=/dev/rdsk/????????
Where I have the question marks is the problem.
How do I find out what the... (4 Replies)
Discussion started by: shorty
4 Replies
2. Filesystems, Disks and Memory
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I have been using a computer to keep track of inventory for my business. I am pretty sure it runs on Unix. In the back of the computer there is some sort of PCI card that has about 8 RJ-11 ports on it. I use that card to connect the Unix system to my 3 VT-220 terminals. I use a simple 6... (1 Reply)
Discussion started by: john202
1 Replies
4. Slackware
Hi Guys,
I'm trying to install slackware 10.2 on a on compaq laptop with Sansung
HM121HI hard drive but I wonder what kernel should I use so it can recognize the had disk. Initially I've tried using sata.i and then try to use the fdisk utility to create the new partiotions but doesn't seem... (0 Replies)
Discussion started by: hariza
0 Replies
5. Solaris
Guys,
I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem.
I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80.
I connected it powered it up and at OK prompt did : boot -r
system comes up and complains about not... (6 Replies)
Discussion started by: ajnabi
6 Replies
6. UNIX for Dummies Questions & Answers
Hello,
I have a machine that has software based RAID. One of the hard drives failed. The problem is that the old systems administrator created LVM and then RAID. My understanding is that RAID had to be created before and then the LVM's. Is there someway to install the new drive without loosing... (2 Replies)
Discussion started by: mojoman
2 Replies
7. Ubuntu
Hi to all,
I have the problem that a laptops with windows XP cannot startup even in safe mode nor using last good known configuration. I have a Ubuntu 10.10 Live CD and booting from it I can read the Hard Drive.
I need to do a backup the Hard Drive from XP laptop and I want to connect this... (5 Replies)
Discussion started by: cgkmal
5 Replies
8. Solaris
Hi All
I connect to my SunBlade using the keyboard/mouse provided by the sun. Now I would like to connect to it using my dell laptop running on Windows 7.
I have connected the laptop to the SunBlade using just a one crossover 9-pin connector using the free/basic version of the terminal... (24 Replies)
Discussion started by: tomicmanka
24 Replies
9. AIX
I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can... (5 Replies)
Discussion started by: mpeter05
5 Replies
EHCI(4) BSD Kernel Interfaces Manual EHCI(4)
NAME
ehci -- USB Enhanced Host Controller driver
SYNOPSIS
device ehci
DESCRIPTION
The ehci driver provides support for the USB Enhanced Host Controller Interface, which is used by USB 2.0 controllers.
EHCI controllers are peculiar in that they can only handle the USB 2.0 protocol. This means that they normally have one or more companion
controllers (i.e., ohci(4) or uhci(4)) handling USB 1.x devices. Consequently each USB connector is electrically connected to two USB con-
trollers. The handling of this is totally automatic, but can be noticed since USB 1.x and USB 2.0 devices plugged in to the same connector
appear to connect to different USB busses.
SEE ALSO
ohci(4), uhci(4), usb(4), xhci(4)
HISTORY
The ehci device driver first appeared in FreeBSD 5.1.
LOADER TUNABLES
When the kernel has been compiled with options USB_DEBUG, some tunables become available that affect the behavior of ehci. These tunables
can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).
hw.usb.ehci.lostintrbug
This tunable enables the lost interrupt quirk. The default value is 0 (off).
hw.usb.ehci.iaadbug
This tunable enables the EHCI doorbell quirk. The default value is 0 (off).
hw.usb.ehci.no_hs
This tunable disables USB devices to attach like HIGH-speed ones and will force all attached devices to attach to the FULL- or LOW-
speed companion controller. The default value is 0 (off).
BSD
March 4, 2012 BSD