02-08-2011
Installing LAN adapter
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware' I choose the "Add new LAN adapter". In the list of tabs, I get the Realtek 8139 (software, in fact, as I said, I managed to upload it regularly). After selecting the adapter from the list, I select the speed that set to "Auto". After the confirmation of all, I get the following error: "Please verify adapter is set to the configuration just entered. No protocol stacks available on the system are supported on this device".
Have you any suggestions? I missed some step during the procedure?
Thank you all.
Vincenzo.
10 More Discussions You Might Find Interesting
1. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
2. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
3. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
4. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
5. Linux
Hi all,
I wanted to install the latest version of firefox 2 but it seems when I attempt to install it, it seems to be saying it is looking for c libraries version 2.3? I believe I currently have an older version of the c libraries. I am currently running Sun's JDS Linux 2003. My Mozilla web... (1 Reply)
Discussion started by: scriptingmani
1 Replies
6. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
7. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
8. Red Hat
I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable
Reboot with lan cable:
The hostname is ubunut
Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies
9. AIX
Hi,
I want to change from vscsi to npiv. Is it possible to use both on the same adapter, so we can change the systems one by one, or must we place a second FC adapter in the VIO servers?
Thanks,
Ronald (2 Replies)
Discussion started by: ronaldm60
2 Replies
10. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
LEARN ABOUT DEBIAN
rtl8139-diag
RTL8139-DIAG(8) System Manager's Manual RTL8139-DIAG(8)
NAME
rtl8139-diag - EEPROM setup and diagnostic program for ethernet cards based on the Realtek 8129 and 8139 chips.
SYNOPSIS
rtl8139-diag [options]
DESCRIPTION
rtl8139-diag is a program that you can use to diagnose problems with ethernet cards based on the Realtek 8129 or 8139 chip series.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-# <cardnum>
Use card number <cardnum>.
-a, --show_all_registers
Print all registers.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --base-address <port>
Specify port to use.
-A, --Advertise <mediaype>
Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII, Autosense and Autonegotiate.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run rtl8139-diag with the options '-t -1'.
SEE ALSO
mii-diag(8)
AUTHOR
rtl8139-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 RTL8139-DIAG(8)