02-02-2011
for asm and sybase which both use rawdevices of some kind, I usually set ioo -p -o lvm_bufcnt=16
Apart from that you surely could do with a few more gigs of memory as your computational usage is really high for an oracle DB. Apart from that - I think your cpu waits are very high - this usually points to problems with the disk subsystem which could have all kinds of reasons - maybe your async IO settings are too low what usually is the case ... set the maxreqs number to 65536 (smitty aio). Check with iostat -Dl if your disks wait queues are running full and your disk response times. Is the above output from while you are running rman ?
Regards
zxmaus
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
How do you reset the values that vmstat displays?
Vmstat displays a running average from the last the system was restarted on the first line, how do you reset these values without restarting the system? (Solaris 8) (3 Replies)
Discussion started by: kuczerp
3 Replies
2. UNIX for Advanced & Expert Users
i have 2 question about vmstat
1)
pin (pagein) output of vmstat is always zero for our system
what is the meaning of this?
(pout significantly changes depending on the running processes)
2)
sometimes react output
of vmstat is given in K like 44K
sometimes it is given without any unit... (1 Reply)
Discussion started by: gfhgfnhhn
1 Replies
3. UNIX for Dummies Questions & Answers
Hello all
This is a sample vmstat output ...
$ vmstat 2 2
kthr memory page disk faults cpu
r b w swap free re mf pi po fr de sr hx hx hx hx in sy cs us sy id
1 0 0 23105784 7810488 323 767 1742 5 5 0 0 0 0 0 0 683 780 457 43 ... (9 Replies)
Discussion started by: luft
9 Replies
4. UNIX for Advanced & Expert Users
Hello,
I'm seeing this problem with vmstat, where the first line of output always has the same CPU statistics. For example:
neked@nekedmachine:~$ date && vmstat
Fri Jul 24 06:57:08 EDT 2009
procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------
r b swpd ... (0 Replies)
Discussion started by: neked
0 Replies
5. AIX
Hello everybody, When i run Nmon the output is really incomprehensible
vmstat 5
System configuration: lcpu=16 mem=24576MB ent=4.00
kthr memory page faults cpu
----- ----------- ------------------------ ------------ -----------------------... (3 Replies)
Discussion started by: Vit0_Corleone
3 Replies
6. Solaris
Hi all.
I need some assistance with my vmstat output.
We have several oracle db's running on our solaris machine:
SunOS rcworaprd 5.9 Generic_112233-07 sun4u sparc SUNW,Sun-Fire-480R
Recently I bumped up our main Oracle database to use 6 GB instead of 4 GB as vmstat output was showing... (1 Reply)
Discussion started by: jamie_collins
1 Replies
7. AIX
Hi all,
Recently I facing problem with my AIX server. we experience slowness on performance. there are some application installed in this server such as : Oracle 10g database, control-m client agent, and some monitoring tools.
when we're facing the problem we're noticing that vmstat value a... (7 Replies)
Discussion started by: Arief Winanto
7 Replies
8. UNIX for Dummies Questions & Answers
TOP:
top - 17:09:39 up 47 days, 1:34, 13 users, load average: 6.54, 10.96, 11.27
Tasks: 274 total, 3 running, 271 sleeping, 0 stopped, 0 zombie
Cpu0 : 6.0%us, 44.9%sy, 0.0%ni, 48.8%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st
Cpu1 : 6.3%us, 44.4%sy, 0.0%ni, 48.0%id, 0.3%wa, ... (2 Replies)
Discussion started by: stunn3r
2 Replies
9. UNIX for Dummies Questions & Answers
Hi,
Users are reporting performance issue on my Sun Solaris 10 server. I am on the server. I don't see a issue or I might be looking at the wrong thing. Please help.
I don't see anything on sar. it's all zero on that. Not sure why users are reporting high CPU and unresponsive at times. ... (1 Reply)
Discussion started by: samnyc
1 Replies
10. Solaris
Hi,
Recently from the vmstat output in the image attached, the first line of the cpu idle column shows a value of 15. Although the subsequent values show higher than 90, is there a reason why the first value is so low?
Is this a problem?
Thanks. (4 Replies)
Discussion started by: anaigini45
4 Replies
IOSTAT(1) General Commands Manual IOSTAT(1)
NAME
iostat - report I/O statistics
SYNOPSIS
iostat [ drives ] [ interval [ count ] ]
DESCRIPTION
Iostat iteratively reports the number of characters read and written to terminals per second, and, for each disk, the number of transfers
per second, kilobytes transferred per second, and the milliseconds per average seek. It also gives the percentage of time the system has
spent in user mode, in user mode running low priority (niced) processes, in system mode, and idling.
To compute this information, for each disk, seeks and data transfer completions and number of words transferred are counted; for terminals
collectively, the number of input and output characters are counted. Also, each sixtieth of a second, the state of each disk is examined
and a tally is made if the disk is active. From these numbers and given the transfer rates of the devices it is possible to determine
average seek times for each device.
The optional interval argument causes iostat to report once each interval seconds. The first report is for all time since a reboot and
each subsequent report is for the last interval only.
The optional count argument restricts the number of reports.
If more than 4 disk drives are configured in the system, iostat displays only the first 4 drives, with priority given to Massbus disk
drives (i.e. if both Unibus and Massbus drives are present and the total number of drives exceeds 4, then some number of Unibus drives will
not be displayed in favor of the Massbus drives). To force iostat to display specific drives, their names may be supplied on the command
line.
FILES
/dev/kmem
/vmunix
SEE ALSO
vmstat(1)
4th Berkeley Distribution April 29, 1985 IOSTAT(1)