good morning,
anybody know of a good Freeware ping sweeper for Solaris, I've been given the job of finding active IP's on the network, would like a tool which can search for range or address's do you know of anything
cheers
Kie (2 Replies)
I have put TMOUT=1800;export TMOUT in the /etc/profile, put it does not work, by the way the root default shell is sh. but I wana every one including root to terminate the session after setting idle for 1800 seconds. thank for the help. (1 Reply)
All,
I log into Solaris 9 server through a command line at the console and want enable a inactivity timer to log out of the server after 5 minutes. How can it be done? (1 Reply)
I recently installed Solaris 10 on my Sun workstation. I cannot ping using hostname from another computer on the same network.
But I can ping using the IP address. Also I can ping other systems using their hostnames.
Can anyone give some information regarding how to resolve this issue. (4 Replies)
Hello,
I need help, I have the following which save in the result file ping and telnet:port test.
Basically the script works but I should implement a check on ping and telnet command so that ping has 5 seconds threshold and telnet (more important) 10 seconds. Over that threshold ping and... (0 Replies)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Hi All Unix Fellows...
Any encounter high ping timeout in AIX Server ? I scheduled the job to ping all the same segments servers all the time for 2 days without terminate. Found sometimes there are time the ping timeout is quite high ie. 10000ms
but most of time is 0ms. what cause this ? is... (2 Replies)
Hi experts:
I want to do below thing with bash
if ping 192.168.0.1 sucussful then do somthing without delay, if ping failed within 20s, then kill ping and exit
not sure this can use "alarm" to do this.
any code will be welcome
Thanks (1 Reply)
Able to ping the server but not able to login through putty it says network timeout
Please assist (3 Replies)
Discussion started by: Vishal_dba
3 Replies
LEARN ABOUT CENTOS
gem
GEM(4) BSD Kernel Interfaces Manual GEM(4)NAME
gem -- ERI/GEM/GMAC Ethernet device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device gem
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gem_load="YES"
DESCRIPTION
The gem driver provides support for the GMAC Ethernet hardware found mostly in the last Apple PowerBooks G3s and most G4-based Apple hard-
ware, as well as Sun UltraSPARC machines.
All controllers supported by the gem driver have TCP checksum offload capability for both receive and transmit, support for the reception and
transmission of extended frames for vlan(4) and a 512-bit multicast hash filter.
HARDWARE
Chips supported by the gem driver include:
o Apple GMAC
o Sun ERI 10/100 Mbps Ethernet
o Sun GEM Gigabit Ethernet
The following add-on cards are known to work with the gem driver at this time:
o Sun Gigabit Ethernet PCI 2.0/3.0 (GBE/P) (part no. 501-4373)
o Sun Gigabit Ethernet SBus 2.0/3.0 (GBE/S) (part no. 501-4375)
NOTES
On sparc64 the gem driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
using the setenv command or by eeprom(8). If set to ``false'' (the default), the gem driver will use the system's default MAC address for
all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
address.
Supported interfaces having their own MAC address include the on-board Sun ERI 10/100 Mbps on boards equipped with more than one Ethernet
interface and the Sun Gigabit Ethernet 2.0/3.0 GBE add-on cards.
SEE ALSO altq(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)HISTORY
The gem device driver appeared in NetBSD 1.6. The first FreeBSD version to include it was FreeBSD 5.0.
AUTHORS
The gem driver was written for NetBSD by Eduardo Horvath <eeh@NetBSD.org>. It was ported to FreeBSD by Thomas Moestl <tmm@FreeBSD.org> and
later on improved by Marius Strobl <marius@FreeBSD.org>. The man page was written by Thomas Klausner <wiz@NetBSD.org>.
BSD December 25, 2009 BSD