01-25-2011
Hi,
I would try to export and reimport the volumegroup in question on the inactive node. Make sure you keep the correct VG Major number (you can import using the -V flag).
If it finds all PVs you should just sync the cluster config and than try again. If it has problems during the import you can take it from there. I had similar issues after migrating storage across disks - duplicate pvid's on some disks - the cluster did not like that much.
Hope that helps,
regards
zxmaus
8 More Discussions You Might Find Interesting
1. High Performance Computing
I have rcently setup a 4 node cluster running sun cluster 3.2
and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename>
this worked ok.
theni I tried to siwitch the zone to node a thei work... (14 Replies)
Discussion started by: lesliek
14 Replies
2. Solaris
Hi,
I am running Solaris 10 + VCS 5 in one of our environment. Recently one of my colleague configured all resources in a single service group.( ie, one service group which has all resources) ,Usually we create seperate service groups for Hardware & for application.
For eg: SYS_HW_GRP, will... (0 Replies)
Discussion started by: mpics66
0 Replies
3. AIX
Hi,
I have a requirement to monitor the HACMP Resource Groups. At present in my environment, if the Resource Groups fail over from preferred node to Secondary node we dont get notification.
Can some one help me in creating a scrript. I have more than one RG online. (Max 4 Resource Groups in... (2 Replies)
Discussion started by: srnagu
2 Replies
4. AIX
Hi,
I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over)
Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Discussion started by: aixromeo
6 Replies
5. AIX
Hi,
I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide:
kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02.
I'm using nfs4 with filesystem for nfs is: /sapnfs
Cluster start without problems. But I cannnot move RG (with... (3 Replies)
Discussion started by: giobuon
3 Replies
6. AIX
Hello. I am Running AIX 6.1 and PowerHA 6.1
I have an active/active cluster (Prod/Dev) cluster. Each side will failover to the other.
I have on my prod side an active volume group with a file system. The VG is imported on both nodes and active (varried on, file system mounted) on the prod... (3 Replies)
Discussion started by: mhenryj
3 Replies
7. AIX
Hi all, I have the following in hacmp.out for bringing Resource group online.
Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems.
+main1_rg_01:cl_activate_vgs STATUS=0
+main1_rg_01:cl_activate_vgs typeset -li STATUS
+main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies
8. AIX
Hello all,
I'm working to fix a two-node SysMirror cluster that uses NFS mounts from a NetApp appliance as the data repository. Currently all the NFS mounts/unmounts are called from the application controller scripts, and since file collection isn't currently working, (One fight at at time... (3 Replies)
Discussion started by: ZekesGarage
3 Replies
LEARN ABOUT HPUX
vxsplitlines
vxsplitlines(1M) vxsplitlines(1M)
NAME
vxsplitlines - show disks with conflicting configuration copies in a cluster
SYNOPSIS
vxsplitlines [-g diskgroup] [-c daname]
DESCRIPTION
If you import portions of a disk group on different systems, this can lead to conflicting configuration copies on the disks of the disk
group.
If the configuration information in a disk group is ambiguous, it may not be possible for Veritas Volume Manager to determine which config-
uration copy is most up-to-date. (This is usually termed a serial split brain (SSB) condition when it occurs in a cluster.) You cannot
import a disk group in this state unless you specify which disk's configuration copy to use.
You can use the vxsplitlines command to see which disks in a disk group have conflicting configuration copies, and use this information
together with your knowledge of the history of the disk groups' usage to determine which configuration copy is most valid.
The output from vxsplitlines displays the vxdg commands that you can run to import the disk group using the available configuration copies.
The -o selectcp option of the vxdg import command is used to select the configuration copy to use for the import.
OPTIONS
-c daname Display the SSB IDs for each disk that are stored in the configuration copy on the disk specified by its disk access name.
Note: Although the SSB IDs for some disks may match, this does not necessarily mean that those disks' configuration copies have
recorded all the configuration changes. When viewed from some other configuration copies, the SSB IDs of the same disks may not
match.
-g diskgroup
Specifies the disk group. If a disk group is not specified, the default disk group is used as determined from the rules on the
vxdg(1M) manual page.
EXAMPLES
Display the disks on each side of the split in the disk group newdg:
vxsplitlines -g newdg
Display the SSB IDs stored in the configuration copy on disk c2t4d0:
vxsplitlines -g newdg -c c2t4d0
NOTES
The vxsplitlines is primarily intended to be used with private disk groups, but it also works with shared disk groups.
The version number of the disk group must be 110 or greater.
SEE ALSO
vxdg(1M)
Veritas Volume Manager Administrator's Guide
VxVM 5.0.31.1 24 Mar 2008 vxsplitlines(1M)