HACMP resource group State not STABLE Post: 302490601

Sponsored Content

Operating Systems AIX HACMP resource group State not STABLE Post 302490601 by elmesy on Tuesday 25th of January 2011 08:26:42 AM

01-25-2011

Registered User

HACMP resource group State not STABLE

Hi,

Not sure if this is the correct forum to post this on but maybe a mod could move it if not.

When trying to move a HACMP resource group between lpars on AIX I receive the following.

State not STABLE/RP_RUNNING or ibcasts Join for node 2 rejected,
Clearing in join protocol flag
Attempting to recover resource group from error
"Resource group not found in client configuration"
echo '+BrokerMB02rg:clvaryonvg prmb02vg[808]' LC_ALL=C 0516-052 varyonvg: Volume group cannot be varied
on without a quorum. More physical volumes in the group must be active. Run diagnostics on inactive PVs.

When these errors are received the resource group then starts back up on the original node.

I have checked the LV's and Quorum is disabled and there are nbo stale PV's

Any help or pointers in the right direction would be much aprreciated.

Thanks,

Matt

Last edited by elmesy; 01-26-2011 at 05:04 AM..

elmesy

View Public Profile for elmesy

Find all posts by elmesy

8 More Discussions You Might Find Interesting

1. High Performance Computing

sun Cluster resource group cant failover

I have rcently setup a 4 node cluster running sun cluster 3.2 and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename> this worked ok. theni I tried to siwitch the zone to node a thei work...

2. Solaris

Solaris + VCS , move a resource to another group

Hi, I am running Solaris 10 + VCS 5 in one of our environment. Recently one of my colleague configured all resources in a single service group.( ie, one service group which has all resources) ,Usually we create seperate service groups for Hardware & for application. For eg: SYS_HW_GRP, will...

3. AIX

Resource Group Monitoring

Hi, I have a requirement to monitor the HACMP Resource Groups. At present in my environment, if the Resource Groups fail over from preferred node to Secondary node we dont get notification. Can some one help me in creating a scrript. I have more than one RG online. (Max 4 Resource Groups in...

4. AIX

Adding a Volume Group to an HACMP Resource Group?

Hi, I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over) Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes...

5. AIX

HACMP, NFS cross-mount problem. Can not move resource group

Hi, I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide: kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02. I'm using nfs4 with filesystem for nfs is: /sapnfs Cluster start without problems. But I cannnot move RG (with...

6. AIX

Adding existing VG to powerHA Resource group

Hello. I am Running AIX 6.1 and PowerHA 6.1 I have an active/active cluster (Prod/Dev) cluster. Each side will failover to the other. I have on my prod side an active volume group with a file system. The VG is imported on both nodes and active (varried on, file system mounted) on the prod...

7. AIX

Power HA 6.1 Bring Resource group online issue

Hi all, I have the following in hacmp.out for bringing Resource group online. Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems. +main1_rg_01:cl_activate_vgs STATUS=0 +main1_rg_01:cl_activate_vgs typeset -li STATUS +main1_rg_01:cl_activate_vgs...

8. AIX

Sysmirror 7.1.3 Resource Group NFS mounts

Hello all, I'm working to fix a two-node SysMirror cluster that uses NFS mounts from a NetApp appliance as the data repository. Currently all the NFS mounts/unmounts are called from the application controller scripts, and since file collection isn't currently working, (One fight at at time...

LEARN ABOUT REDHAT

vgremove

VGREMOVE(8)						      System Manager's Manual						       VGREMOVE(8)

NAME

       vgremove - remove a volume group

SYNOPSIS

       vgremove [-d|--debug] [-h|--help] [-v|--verbose] VolumeGroupName [VolumeGroupName...]

DESCRIPTION

       vgremove  allows you to remove one or more volume groups.  The volume group(s) must not have any logical volumes allocated and must also be
       inactive (see vgchange(8) ).

   OPTIONS
       -d, --debug
	      Enables additional debugging output (if compiled with DEBUG).

       -h, --help
	      Print a usage message on standard output and exit successfully.

       -v, --verbose
	      Gives verbose runtime information about vgremove's activities.

DIAGNOSTICS

       vgremove returns an code code of 0 for success and > 0 for error:

       1  no volume group name on command line
       2  error setting up freed physical volume
       3  error writing freed physical volume(s) to disk(s)
       4  error removing volume group from lvmtab
       5  can't remove volume group containing logical volumes
       6  invalid volume group name
       7  volume group is active
       8  not all physical volumes are online
       9  error accessing volume group
       10 error reading volume group data from disk(s)

       95 driver/module not in kernel
       96 invalid I/O protocol version
       97 error locking logical volume manager
       98 invalid lvmtab (run vgscan(8))
       99 invalid command line

See also
       lvm(8), vgcreate(8), vgreduce(8)

AUTHOR

       Heinz Mauelshagen <Linux-LVM@Sistina.com>

Heinz Mauelshagen						     LVM TOOLS							       VGREMOVE(8)