01-20-2011
royalliege - entries in fault manager have to be cleared out manually. They will remain until they are cleared. If you look at the output, you will see a date of when the error occurred. I don't know your system, but that error could be from years ago. Even though the initial problem has been resolved, the error will need to be cleared. For example, if you have a failed DIMM and you see it listed in the fault manager, you will still need to clear the message after the DIMM is replaced.
This User Gave Thanks to garskoci For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
Hello
We have a power supply in an x4100 (x86) and it seems to be faulty but it is still working!?! (this box only has one PSU). We are getting Orange flashing warning light on the front of the box and the LED labelled “rear PSu” is solid orange ...We don't seem to have had any syslog error... (8 Replies)
Discussion started by: hcclnoodles
8 Replies
2. Solaris
Hi All,
I replace a sub-mirror of a mirrored volume by using below command:
#metadetach d10(mirror) d11(striped)
#metattach d10 d13(other striped)
With above process I successfully replaced a faulty volume. I want to knoow if the process I followed is right. Or if not, what... (5 Replies)
Discussion started by: naw_deepak
5 Replies
3. Solaris
Hi people,
Hoping someone has maybe done this before?
I'm trying to run fmadm from the xcsf prompt on an M4000 and it won't run, complaining about insufficient privileges, even though the user has supposedly been setup with fieldeng privileges.
Anyone got any ideas?
Cheers
Rgrds... (10 Replies)
Discussion started by: callmebob
10 Replies
4. Solaris
Hi,
Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great.
# uname –a
SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4
#df -k
Filesystem kbytes used... (3 Replies)
Discussion started by: phanidhar6039
3 Replies
5. HP-UX
Requirement to remove a faulty mirrored disk from hp-ux LVM
<root@pdwp1s>/etc # vgdisplay -v /dev/vg00
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't... (9 Replies)
Discussion started by: Shirishlnx
9 Replies
6. HP-UX
Hi,
Have mirrored the primary disk to 3 .
Server and OS:
# uname -a
HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license
# model
9000/800/L3000-7x
# strings /etc/lvmtab
/dev/vg00
+F@<
/dev/dsk/c1t2d0
/dev/dsk/c2t2d0
/dev/dsk/c2t0d0
But now I have only 1 disk... (5 Replies)
Discussion started by: Shirishlnx
5 Replies
7. Solaris
Hi,
I'm trying to generate an alert related to Power Supply Failure.
As its difficult to generate such an event, Is it possible to set the status of a Power Supply Unit as "Faulty"
Any ideas are welcome and highly appreciated
-Thanks (3 Replies)
Discussion started by: justsam
3 Replies
8. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
9. Hardware
Hello,
Following parts need to be replaced in a frame as suggested by IBM
1. Flexible Cable
2. Service Processor Card
Would these faulty parts impact all lpars which are there in this frame?
Best regards,
Vishal (5 Replies)
Discussion started by: admin_db
5 Replies
10. UNIX for Beginners Questions & Answers
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies