I have to cd into /sbin in order to use ifconfig to check out my network cards. This has only started to happen since I downloaded the last update from RedHat(The machine runs RedHat 8.0).
Does anyone know what happened?
More importantly, are there any sources that can help me with this... (3 Replies)
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
hey,
I know that ifconfig on linux systems is identical to win ipconfig.
I wanted to know if there is a linux distribution (new or old) that uses the ipconfig command.
thanks alot :) (2 Replies)
hi,
i want to know how to grep inet address for below
below is the output of ifconfig command
/home/JA> ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:0A:5B:2E:E9
inet addr:161.239.203.18 Bcast:161.239.203.127 Mask:255.255.255.128
UP BROADCAST RUNNING... (3 Replies)
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Hi all,
I am getting some error messages during bootup
ifconfig :<hostname> bad address
and some more messages related to it.
I some how checked the /etc/hostanem.hme0 /etc/hosts file.
Entries in these files were proper.
If I am running the following command from root:
... (5 Replies)
Hi there,
I need your help in understanding the below Solaris 10 ifconfig output;
athnetspns02>ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0:... (2 Replies)
So, I have this script that makes a call to ifconfig to pull the interface information and report it. When I log on to the machine the script works just fine. But, if I'm on a remote machine and I make a call like this.
ssh user@server ./script.bash
I get an error saying that the IFCONFIG command... (9 Replies)
Discussion started by: Binary Buddha
9 Replies
LEARN ABOUT MINIX
ifconfig
IFCONFIG(8) System Manager's Manual IFCONFIG(8)NAME
ifconfig - configure a TCP/IP device
SYNOPSIS
ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv]
DESCRIPTION
Ifconfig initializes a TCP/IP device setting the IP address and/or netmask. It will report the address and netmask set. This command may
be used if the system has not been configured properly yet. It is only used at boot time to set a fixed address for a system without a
physical ethernet. Normally the inet task will find it out by itself from the RARP server.
OPTIONS -h The decimal TCP/IP address to set.
-n The netmask to set.
-i Don't set the IP address or netmask if already set. This way ifconfig cannot interfere if the numbers have been found out by RARP.
-v Report IP address and netmask. This is the default action if there are no other options.
SEE ALSO hostaddr(1), rarpd(8), set_net_default(8), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
IFCONFIG(8)