12-09-2010
you can patch the local zone only... but the kernel is shared with the global zone. so, the KJP can only be installed in the global zone and the dependend patches also...
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
As in the solaris material i know that the patch is added through the command "patchadd <patch no.>".
But i need to know, what are all the steps we have to follow while applying a patch in a production server. My friend says that we have to detach mirror before applying patch and not... (6 Replies)
Discussion started by: Sesha
6 Replies
2. Solaris
Hello,
The 10_Recommended update failed on 3 of 191, which was patch 119254-73 (the 1st 2 patches were skipped). I looked up the patch on Sunsolve (http://sunsolve.sun.com/search/document.do?assetkey=1-21-119254), which stated that 121133-02 was a required patch for 119254-73. I did a "showrev... (7 Replies)
Discussion started by: stringman
7 Replies
3. Solaris
Hello,
As explained, I've encountered an issue while installing Solaris 10 SPARC Recommended Patch Cluster (2009.10.23).
Actually, patch no 120011-14 stops with the following error:
ERROR: attribute verification of </var/run/.patchSafeMode/root/usr/bin/passwd> failed
file type <f>... (6 Replies)
Discussion started by: a.mauger
6 Replies
4. Solaris
I'm trying to setup our jumpstart server to automatically apply the latest patch cluster during installs, but I'm running into an issue. Every time Jumpstart runs it has this error. Obviously it's processing the patch_order file, so I'm not sure what I'm missing.
... (0 Replies)
Discussion started by: christr
0 Replies
5. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
6. Solaris
I have a question regarding installing recommended patch clusters via ZFS snapshots. Someone wrote a pretty good blog about it here:
Initial Program Load: Live Upgrade to install the recommended patch cluster on a ZFS snapshot
The person's article is similar to what I've done in the past. ... (0 Replies)
Discussion started by: christr
0 Replies
7. UNIX for Dummies Questions & Answers
what are the typical steps used by system adminstrators while applying an application patch upgrade (1 Reply)
Discussion started by: ramky79
1 Replies
8. Solaris
Dear All,
Has Oracle stopped updating Solaris 10 recommended patch cluster ? From suport.oracle.com i could see the last patch bundle was released on 11th july and there has been no updates after that.
Does anyone know about any official announcement from oracle on this ?
Thanks ... (1 Reply)
Discussion started by: abhi_8029
1 Replies
9. Ubuntu
I have applied a patch using this command:
patch -p1 < (file)
then I did git commit -a.
Now I want to recompile the kernel for making this patch live.
Should I use
make oldconfig
or
make localmodconfig
After that,
make -j$(grep -c "processor" /proc/cpuinfo)
sudo make... (1 Reply)
Discussion started by: BHASKAR JUPUDI
1 Replies
10. Debian
The version of Samba in our billing server is 4.1.17-Debian.
I have been reminded by our management to implement the patch for Samba on this server.
However, I am not sure how to implement the patch. I have browsed some websites for the correct patch to implement for Samba 4.1.17, and the patch... (11 Replies)
Discussion started by: anaigini45
11 Replies
LEARN ABOUT OPENSOLARIS
native
native(5) Standards, Environments, and Macros native(5)
NAME
native - native branded zone
DESCRIPTION
The native brand uses the branded zones framework described in brands(5) to run zones installed with the same software as is installed in
the global zone. The system software must always be in sync with the global zone when using a native brand.
SUB-COMMANDS
The following native brand-specific subcommand options are supported in zoneadm(1M).
attach [-u] [-b patchid]...
For native zones, zoneadm checks package and patch levels on the machine to which the zone is to be attached. If the packages/patches
that the zone depends on from the global zone are different (have different revision numbers) from the dependent packages/patches on
the source machine, zoneadm reports these conflicts and does not perform the attach. If the destination system has only newer dependent
packages/patches (higher revision numbers) than those on the source system, you can use the -u option to update the attached zone to
match the -revision packages and patches that exist on the new system. With -u, as in the default behavior, zoneadm does not perform an
attach if outdated packages/patches are found on the target system.
For native zones, one or more -b options can be used to specify a patch ID for a patch installed in the zone. These patches will be
backed out before the zone is attached or, if -u was also specified, updated.
install [-a archive] | [-d path] [-p] [-s] [-u] [-v] [-b patchid]...
The native brand installer supports installing the zone from either the software already installed on the system or from an image of an
installed system running the same release. This can be a full flash archive (see flash_archive(4)) or a cpio(1) or pax(1) "xustar" ar-
chive. The cpio archive be compressed with gzip or bzip2. The image can also be a level 0 ufsdump(1M), a path to the top-level of a
system's root tree, or a pre-existing zone path.
With no options the zone is installed using same software as is running the global zone.
To install the zone from a system image either the -a or -d is required. Either the -u or -p option is also required in this case.
-a archive
The path to a flash_archive(4), cpio(1), or pax(1) "xustar" archive, or a level0 ufsdump(1M), of an installed system. cpio archives
may be compressed using gzip or bzip2.
-b patchid
One or more -b options can be used to specify a patch ID for a patch installed in the system image. These patches will be backed
out during the installation process.
-d path
The path to the root directory of an installed system. If path is a hyphen (-), the zonepath is presumed to be already populated
with the system image.
-p
Preserve the system configuration after installing the zone.
-s
Install silently.
-u
Run sys-unconfig(1M) on the zone after installing it.
-v
Verbose output from the install process.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWzoneu |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
cpio(1), pax(1), zlogin(1), zonename(1), sys-unconfig(1M), ufsdump(1M), zoneadm(1M), zonecfg(1M), flash_archive(4), attributes(5),
brands(5), privileges(5), zones(5), lx_systrace(7D)
SunOS 5.11 13 Feb 2009 native(5)