Sponsored Content
Top Forums UNIX for Advanced & Expert Users Multihomed server, eth1 not working Post 302478680 by msarro on Wednesday 8th of December 2010 02:58:49 PM
Old 12-08-2010
Prior issues have been resolved. I used the method detailed here to get the interfaces up and running:
Routing for multiple uplinks/providers

All traffic appears to be working correctly; what comes in on one port leaves the correct port. Well, save for one thing. SNMP isn't working correctly. When an SNMP GET request comes in on eth1, the SNMP agent still appears to be sending out responses on bond0, so they're never retrieved by the manager. Any ideas??
 

10 More Discussions You Might Find Interesting

1. Programming

Multihomed Client

Hi, I am writing a socket program at the moment that uses both of the clients network interfaces. The program tries to create two socket connections to the server over a LAN connection and a GPRS connection. I have tried to update the routing table using the route command but that proved... (0 Replies)
Discussion started by: mhynes
0 Replies

2. IP Networking

Multihomed DNS Clients?

I'm not sure it that's the right term for what I'm asking about, but it's the best I could come up with. Here is my situation... I'm setting up a network using OpenVPN. The clients I'm setting up will need to be able to access their own DNS servers (to resolve internal names at their location)... (4 Replies)
Discussion started by: deckard
4 Replies

3. UNIX for Dummies Questions & Answers

/etc/rc.d/net - eth1

I just installed Crux on my laptop, which means I'll have to configure /etc/rc.d/net to adapt to my wireless internet. When I ran Linux before, I connected through eth1. How should I configure the /etc/rc.d/net file accordingly? Thanks for reading, Octal. (0 Replies)
Discussion started by: Octal
0 Replies

4. Red Hat

ifcfg-eth0 and eth1 is N/A

when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in /etc/sysconfig/network-scripts/. what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies

5. UNIX for Advanced & Expert Users

Eth1 turn off by itself after reboot

Hi, Recently we discovered the eth1 of one of the server turn off by itself when the system reboot. Could someone please advise how to fix it? Thanks (4 Replies)
Discussion started by: beeloo
4 Replies

6. IP Networking

Multihomed can not ping gateway

Hello this is my first post at this forum. Apologize for my lack of network understanding but Im posting to learn. I have a problem reaching default gateway 10.18.110.1 If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping. cat... (11 Replies)
Discussion started by: vettec3
11 Replies

7. IP Networking

HOWTO: Linux multihomed dns client

The Linux resolver queries all nameservers in the order they are listed in /etc/resolver.conf. If a nameserver times out, it advances on to the following nameserver. But, if a nameserver returns "not found" (NXDOMAIN) it stops. This behaviour is problematic when you need to resolve names from... (0 Replies)
Discussion started by: colemar
0 Replies

8. UNIX for Dummies Questions & Answers

Removing IP address from eth1 on SUSE

Hello folks; I have a NIC card on my SUSE 10.3 server with eth0 & eth1 configured with two IP addresses (172.16.5.3 & 172.16.5.4) I'd like to remove the IP assigned to eth1 (172.16.5.4). i think i know i can go into ifcfg-eth1 and edit it but before i do that, i want to know if there's a better... (2 Replies)
Discussion started by: Katkota
2 Replies

9. IP Networking

HOWTO: Linux multihomed dns client - reverse lookup

The following thread is closed: 133552-howto-linux-multihomed-dns-client (Sorry I am not allowed to post URLs) Therefore I write this append in an own thread. The HOWTO in the referenced thread helped me a lot and I only want to append how to make reverse lookup working for a local zone: ... (0 Replies)
Discussion started by: scheruga
0 Replies

10. Ubuntu

Ubuntu Server in VM - DHCP Server not working

Hello. Doing my first steps in Linux and while trying to configure a DHCP server in Linux i encountered some problems: TOPOLOGY: - Laptop with Windows 8.1 - VM Player 12 with Linux installed (Ubuntu Server 14.04) - ICS-DHCP-SERVER installed and running - Another LAPTOP conected to a... (1 Reply)
Discussion started by: Portuguevos
1 Replies
Match-all classifier in tc(8)                                          Linux                                         Match-all classifier in tc(8)

NAME
matchall - traffic control filter that matches every packet SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ] DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it. OPTIONS
action ACTION_SPEC Apply an action from the generic actions framework on matching packets. classid CLASSID Push matching packets into the class identified by CLASSID. skip_sw Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter- face, operation will fail. skip_hw Do not process filter by hardware. EXAMPLES
To create ingress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle ffff: ingress tc filter add dev eth1 parent ffff: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To create egress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle 1: root prio tc filter add dev eth1 parent 1: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To sample one of every 100 packets flowing into interface eth0 to psample group 12: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: matchall action sample rate 100 group 12 SEE ALSO
tc(8), iproute2 21 Oct 2015 Match-all classifier in tc(8)
All times are GMT -4. The time now is 11:27 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy