Sponsored Content
Full Discussion: remove interface from dladm
Operating Systems Solaris remove interface from dladm Post 302475063 by DukeNuke2 on Friday 26th of November 2010 10:09:42 AM
Old 11-26-2010
as allready said in my first post:

you can't remove them... they are present in your system so dladm "show-dev" will show them!
 

9 More Discussions You Might Find Interesting

1. Solaris

dladm use

Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this: dladm create aggr -d ce0 -d ce1 key Do I need to... (1 Reply)
Discussion started by: hshapiro
1 Replies

2. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

3. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

4. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

5. Solaris

ifconfig -a vs dladm show-dev and IP ?

Can anyone please explain what does these means ? # dladm show-dev nxge0 link: up speed: 1000 Mbps duplex: full nxge1 link: up speed: 1000 Mbps duplex: full e1000g0 link: up speed: 1000 Mbps duplex: full e1000g1 ... (6 Replies)
Discussion started by: dehetoxic
6 Replies

6. Solaris

[beginner] dladm create-bridge

hello everyone, I'm a new user and unix-beginner. I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Discussion started by: kimj
12 Replies

7. Shell Programming and Scripting

remove brackets and put it in a column and remove repeated entry

Hi all, I want to remove the remove bracket sign ( ) and put in the separate column I also want to remove the repeated entry like in first row in below input (PA156) is repeated ESR1 (PA156) leflunomide (PA450192) (PA156) leflunomide (PA450192) CHST3 (PA26503) docetaxel... (2 Replies)
Discussion started by: manigrover
2 Replies

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

9. Solaris

Solaris 11.4.2.3.0 - dladm link names mapping

Hi all, I have never wondered where is the mapping of the link names to physical device path display under dladm show-phys until today. fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
Discussion started by: javanoob
1 Replies
xge(7D) 																   xge(7D)

NAME
xge - Neterion Xframe 10Gigabit Ethernet Network Adapter driver SYNOPSIS
/dev/xge DESCRIPTION
The xge 10 Gigabit Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider Interface, dlpi(7P), on S2IO Xframe 10-Gigabit Ethernet Network Adapter. The xge driver functions includes controller initialization, frame transmit and receive, promiscuous and multicast support, TCP and UDP checksum offload (IPv4 and IPv6), 9622-byte jumbo frame, and error recovery and reporting. The xge driver and hardware support the 10GBase-SR/W, LR/W, and ER/W 802.3 physical layer. APPLICATION PROGRAMMING INTERFACE
The cloning, character-special device /dev/xge is used to access all Xframe devices installed within the system. The xge driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of xge instances and for xge instances to be aggregated. See dladm(1M) for more details. The values returned by the driver in the DL_INFO_ACK primitive in response to the DL_INFO_REQ are as follows: o Maximum SDU is 9600. o Minimum SDU is 0. o DSLAP address length is 8 bytes. o MAC type is DL_ETHER. o SAP length value is -2 meaning the physical address component is followed immediately by a 2-byte sap component within the DLSAP address. o Broadcast address value is Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF). CONFIGURATION
By default, the xge driver works without any configuration file. You can check the running-time status of a device instance using ndd(1M). Currently, the driver provides an interface to print all hard- ware statistics. For example, to print statistics of device xge0: #ndd /dev/xge0 stats tmac_data_octets 772 tmac_frms 15 tmac_drop_frms 0 tmac_bcst_frms 6 tmac_mcst_frms 6 ... rmac_vld_frms 13 rmac_fcs_err_frms 0 rmac_drop_frms 0 rmac_vld_bcst_frms 7 rmac_vld_mcst_frms 11 rmac_out_rng_len_err_frms 0 rmac_in_rng_len_err_frms 0 rmac_long_frms 0 ... not_traffic_intr_cnt 242673 traffic_intr_cnt 28 ... FILES
/dev/xge xge special character device ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |Architecture | | +-----------------------------+-----------------------------+ SEE ALSO
dladm(1M), ndd(1M), attributes(5), streamio(7I), dlpi(7P) Writing Device Drivers STREAMS Programming Guide Network Interfaces Programmer's Guide 3 Oct 2005 xge(7D)
All times are GMT -4. The time now is 05:59 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy