Thinking of using our San for network backups..
Have a Netra 240 being installed and planning to get some space on our San.
Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Hi,
I have an existing SUN server that has a SAN storage installed on it. It also has softwares like Appwrox(scheduler), Taradata (database client), Samba Share and a few more installed on it.
Now suppose that I have a new unix server server and i switch the same SAN store from the old unix... (1 Reply)
I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Hi,
I have configured our SAN Storage to be connected to our new SUN T5220.
On the SAn it looks all fine
on the server I do not see any connection:
cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected ... (4 Replies)
HI all,
I had recently change the Server storage from EMC to the IBM SAN.
but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server.
When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Hi,
We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN.
The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes).
I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
hi all,
I am on solaris 10 1/13 and new to SAN storage.
I am required to connect to the LUNs on the SAN storage and is asked to provide the WWN information to the storage administrator.
Right now, it will be just 1 connection from a single hba port to the FCport on the storage directly,... (1 Reply)
Discussion started by: javanoob
1 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)