AIBS(4) 						   BSD Kernel Interfaces Manual 						   AIBS(4)

NAME

     aibs -- ASUSTeK AI Booster ACPI ATK0110 voltage, temperature and fan sensor

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device acpi
	   device aibs

     Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):

	   acpi_load="YES"
	   aibs_load="YES"

DESCRIPTION

     The aibs driver provides support for the voltage, temperature and fan sensors available through the ATK0110 ASOC ACPI device on ASUSTeK moth-
     erboards.	The number of sensors of each type, as well as the description of each sensor, varies according to the motherboard.

     The driver supports an arbitrary set of sensors, provides descriptions regarding what each sensor is used for, and reports the current values
     as well as the supposed range specifications of each sensor's input as defined by the motherboard manufacturer through ACPI.

     The range specifications are as follows:

     o	 Voltage sensors have a lower and an upper range specification.

     o	 Temperature sensors have two upper specifications.

     o	 Fan sensors may either have only the lower specification, or, depending on the DSDT, one lower and one upper specification.

     Sensor readings and the range specifications are made available through the sysctl(3) interface, and can be monitored with sysctl(8).  For
     example, on an ASUS V3-P5G965 barebone:

	   > sysctl dev.aibs.0.{volt,temp,fan}
	   dev.aibs.0.volt.0: 1192 850 1600
	   dev.aibs.0.volt.1: 3312 2970 3630
	   dev.aibs.0.volt.2: 5017 4500 5500
	   dev.aibs.0.volt.3: 12302 10200 13800
	   dev.aibs.0.temp.0: 28.0C 80.0C 95.0C
	   dev.aibs.0.temp.1: 55.0C 60.0C 95.0C
	   dev.aibs.0.fan.0: 878 600 7200
	   dev.aibs.0.fan.1: 0 700 7200

	   > sysctl -d dev.aibs.0.{volt,temp,fan}
	   dev.aibs.0.volt:
	   dev.aibs.0.volt.0: Vcore Voltage
	   dev.aibs.0.volt.1:  +3.3 Voltage
	   dev.aibs.0.volt.2:  +5 Voltage
	   dev.aibs.0.volt.3:  +12 Voltage
	   dev.aibs.0.temp:
	   dev.aibs.0.temp.0: CPU Temperature
	   dev.aibs.0.temp.1: MB Temperature
	   dev.aibs.0.fan:
	   dev.aibs.0.fan.0: CPU FAN Speed
	   dev.aibs.0.fan.1: CHASSIS FAN Speed

     Generally, sensors provided by the aibs driver may also be supported by certain other drivers or utilities that access the ISA / LPC or I2C /
     SMBus devices directly.  The precise collection of aibs sensors is comprised of the sensors specifically utilised in the motherboard design,
     which may be supported through a combination of one or more physical hardware monitoring chips.

     The aibs driver, however, provides the following advantages when compared to the native hardware monitoring drivers or other utilities:

     o	 Sensor values from aibs are expected to be more reliable.  For example, voltage sensors in many hardware monitoring chips can only sense
	 voltage from 0 to 2 or 4 volts, and the excessive voltage is removed by the resistors, which may vary with the motherboard and with the
	 voltage that is being sensed.	In aibs, the required resistor factors are provided by the motherboard manufacturer through ACPI; in the
	 native drivers, the resistor factors are encoded into the driver based on the chip manufacturer's recommendations.  In essence, sensor
	 values from aibs are very likely to be identical to the readings from the Hardware Monitor screen in the BIOS.

     o	 Sensor descriptions from aibs are more likely to match the markings on the motherboard.

     o	 Sensor range specifications are supported by aibs.  The range specification is reported for each individual sensor as suggested by the
	 motherboard manufacturer.  For example, the threshold for the CPU temperature sensor is likely to be significantly higher than that for
	 the chassis temperature sensor.

     o	 Support for newer chips in aibs.  Newer chips may miss a native driver, but should be supported through aibs regardless.

SEE ALSO

     sysctl(3), acpi(4), sysctl(8)

HISTORY

     The aibs driver first appeared in OpenBSD 4.7, DragonFly 2.5, NetBSD 6.0 and FreeBSD 9.0.

     An earlier version of the driver, acpi_aiboost, first appeared in FreeBSD 7.0 and NetBSD 5.0.

AUTHORS

     The aibs driver was written for OpenBSD, DragonFly, NetBSD and FreeBSD by Constantine A. Murenin <cnst@FreeBSD.org>, Raouf Boutaba Research
     Group, David R. Cheriton School of Computer Science, University of Waterloo.

     An earlier version of the driver, named acpi_aiboost, was written for FreeBSD by Takanori Watanabe.

BSD
								   April 4, 2010							       BSD