Solved it by myself, but I should have tought about it earlier.
What I forgot was to NAT the adresses from the 192.168.1.0/24 to the 192.168.2.0/24 adresses.
So what I have done.
- Enabled the IPfilter firewall.
- create the file /etc/ipf/ipnat.conf
- restart ipfilter
HI guys/gals
basic question
lets say i am running a network. lets say i am using Win Me.
how would i network Win Me to a computer that has linux and another that has 98 well the 98 is no problem but the linux well i have an idea but i am rusty with linux. No i have rusted out. Would you make... (1 Reply)
I am trying to network two solaris workstations(ultra sparc 5) at home. what shoud I use to build the one of workstations as a http and ftp server and to network with the other workstation?
(please explain to me in detail.. what kind of software or equipment do I need..)
Thanks
John (1 Reply)
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
hi all,
how do i make sure that the new routing should take effect on the os memory right away? what should i run after i add all the new "route add ....".
I have an example below:
bash-2.03# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface... (1 Reply)
I have just installed Solaris 10 for x86. The install seemed to have worked fine, and I have configured my hostname and am able to login and do whatever. However, networking does not seem to have been installed. I have a router which assigns ip address via DHCP. I would have thought Solaris would... (5 Replies)
Hi all
Right, i need to admit Im c4p on networking. I hate it, always have, always will. Here's my problem
Ive got 3 hosts. A B and C. I need to directly contact host C from host A, but at the moment I have to ssh on to B, to then ssh on to C.
so, I need to set up host b, to forward... (3 Replies)
Hi All,
Actually a very basic question this one. I've got a Solaris 10 x86 server box on a network. There are a group of other servers I need to connect to from it, but via a VPN connection. If I install a vpn client on my solaris box, can I configure the VPN connection so it only routes certain... (1 Reply)
Discussion started by: mikecouk
1 Replies
LEARN ABOUT DEBIAN
aggregate-ios
AGGREGATE-IOS(1) General Commands Manual AGGREGATE-IOS(1)NAME
aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short.
SYNOPSIS
aggregate-ios <source_config >optimised_config
DESCRIPTION
Takes cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1). Optimised filters are produced on std-
out.
OPTIONS
None.
DIAGNOSTICS
Any diagnostics produced by aggregate(1) are passed through on stderr.
EXAMPLES
The following configuration fragment:
ip prefix-list AS65530 description Foo, Inc
ip prefix-list AS65530 permit 10.1.0.0/16
ip prefix-list AS65530 permit 10.2.0.0/16
ip prefix-list AS65530 permit 10.2.1.0/24
ip prefix-list AS65530 permit 10.3.0.0/16
ip prefix-list AS65531 description Bar.Com
ip prefix-list AS65531 seq 5 permit 192.168.1.0/24
ip prefix-list AS65531 seq 10 permit 192.168.2.0/24
ip prefix-list AS65531 seq 15 permit 192.168.0.0/19
is optimised as follows:
ip prefix-list AS65530 permit 10.1.0.0/16 le 24
ip prefix-list AS65530 permit 10.2.0.0/15 le 24
ip prefix-list AS65531 permit 192.168.0.0/19 le 24
SEE ALSO aggregate(1)HISTORY
Aggregate-ios was written by Joe Abley <jabley@mfnx.net>.
BUGS
All those in aggregate(1) and then some :)
Joe Abley 2000 November 27 AGGREGATE-IOS(1)