AGGREGATE(1) General Commands Manual AGGREGATE(1)
aggregate - optimise a list of route prefixes to help make nice short filters
aggregate [-m max-length] [-o max-opt-length] [-p default-length] [-q] [-t] [-v]
Takes a list of prefixes in conventional format on stdin, and performs two optimisations to attempt to reduce the length of the prefix
The first optimisation is to remove any supplied prefixes which are superfluous because they are already included in another supplied pre-
fix. For example, 188.8.131.52/24 would be removed if 184.108.40.206/17 was also supplied.
The second optimisation identifies adjacent prefixes that can be combined under a single, shorter-length prefix. For example, 220.127.116.11/24
and 18.104.22.168/24 can be combined into the single prefix 22.214.171.124/23.
Sets the maximum prefix length for entries read from stdin max_length bits. The default is 32. Prefixes with longer lengths will be
discarded prior to processing.
Sets the maximum prefix length for optimisation to max-opt-length bits. The default is 32. Prefixes with longer lengths will not be
subject to optimisation.
Sets the default prefix length. There is no default; without this option a prefix without a mask length is treated as invalid. Use
-p 32 -m 32 -o 32 to aggregate a list of host routes specified as bare addresses, for example.
-q Sets quiet mode -- instructs aggregate never to generate warning messages or other output on stderr.
-t Silently truncate prefixes that seem to have an inconsistent prefix: e.g. an input prefix 126.96.36.199/24 would be truncated to
188.8.131.52/24. Without this option an input prefix 184.108.40.206/24 would not be accepted, and a warning about the inconsistent mask
would be generated.
-v Sets verbose mode. This changes the output format to display the source line number that the prefix was obtained from, together with
a preceding "-" to indicate a route that can be suppressed, or a "+" to indicate a shorter-prefix aggregate that was added by aggre-
gate as an adjacency optimisation. Note that verbose output continues even if -q is selected.
Aggregate exits 0 on success, and >0 if an error occurs.
The following list of prefixes:
is optimised as followed by aggregate (output shown using the -v flag):
aggregate: maximum prefix length permitted will be 24
[ 0] + 220.127.116.11/21
[ 1] - 18.104.22.168/22
[ 2] - 22.214.171.124/22
[ 3] 126.96.36.199/22
[ 4] 188.8.131.52/22
[ 5] 184.108.40.206/22
[ 0] + 220.127.116.11/21
[ 6] - 18.104.22.168/22
[ 7] - 22.214.171.124/22
[ 8] - 126.96.36.199/23
[ 9] 188.8.131.52/19
[ 10] 184.108.40.206/21
[ 0] + 220.127.116.11/15
[ 11] - 18.104.22.168/16
[ 12] - 22.214.171.124/16
Note that 126.96.36.199/22 and 188.8.131.52/22 were combined under the single prefix 184.108.40.206/21, and 220.127.116.11/23 was suppressed
because it was included in 18.104.22.168/22. The number in square brackets at the beginning of each line indicates the original line num-
ber, or zero for new prefixes that were introduced by aggregate.
The output without the -v flag is as follows:
Aggregate was written by Joe Abley <firstname.lastname@example.org>, and has been reasonably well tested. It is suitable for reducing customer prefix fil-
ters for production use without extensive hand-proving of results.
Autoconf bits were donated by Michael Shields <email@example.com>. The -t option was suggested by Robin Johnson <rob-
firstname.lastname@example.org>, and the treatment of leading zeros on octet parsing was changed following comments from Arnold Nipper
An early version of aggregate would attempt to combine adjacent prefixes regardless of whether the first prefix lay on an appropriate bit
boundary or not (pointed out with great restraint by Robert Noland <email@example.com>).
Common unix parsing of IPv4 addresses understands the representation of individual octets in octal or hexadecimal, following a "0" or "0x"
prefix, respectively. That convention has been deliberately disabled here, since resources such as the IRR do not follow the convention,
and confusion can result.
For extremely sensitive applications, judicious use of the -v option together with a pencil and paper is probably advisable.
Joe Abley 2001 November 2 AGGREGATE(1)