Sponsored Content
Top Forums Shell Programming and Scripting Tcl: How to communicate serial port remotely Post 302466592 by Corona688 on Tuesday 26th of October 2010 06:34:30 PM
Old 10-26-2010
Unfortunately I don't know TCL well but I have other suggestions... First off make sure that the port is set to the correct baud rate and mode.
Code:
stty -F /dev/ttyS0 9600 CS8 -cstopb -parenb raw

should set it to 9600-baud, 8-bit, one stop bit, no parity, raw mode(i.e, ctrl-c doesn't send SIGINT!). This doesn't have to be run inside your program, and it ought to remember once run once unless something else changes it(or your system reboots).
 

10 More Discussions You Might Find Interesting

1. Solaris

Communicate Serial Modem using non-Root user

Hi, I'm having a issue on communicating the serial GSM modem in Sun Solaris 5.9 To implement such connectiom, i'm using the "tip -115200 /dev/term/a" command and i successfully get the "connected" status And then i send a "AT" message and receive "OK" response from the modem :D Anyhow,... (0 Replies)
Discussion started by: darontan
0 Replies

2. Solaris

Serial port issue

Hi, I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port. When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies

3. Solaris

Serial port not found

Hi, I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output-- According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies

4. Programming

Programming serial port

Hello! Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements: 1. Serial port is opened in non-canonical mode. 2. All the time I need to check is there something to read. 3. If I have to write something I need to write it... (6 Replies)
Discussion started by: jvrlic
6 Replies

5. Programming

How to tell if a string to serial port has been sent

I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows: SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK); write (SerialPort_Send, pCommandString, strlen (pCommandString)); ... (2 Replies)
Discussion started by: ExDes
2 Replies

6. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies

7. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

8. Solaris

Using PC serial port from ReflectionX

I am using ReflectionX on a windows PC to run an application on a Solaris box. The application uses the serial port and expects a definition like: /dev/ttyb Is there a way to use the PC serial port through ReflectionX? PC is running Windows-XP Solaris Box is: Sun Microsystems sun4u... (1 Reply)
Discussion started by: deanjennings
1 Replies

9. Web Development

Setup Serial Port

I need to set a serial port to 9600 7E1. How do I accomplish this? I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies

10. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
CMAP(5)                                                         File Formats Manual                                                        CMAP(5)

NAME
cmap - format of .cmap files (color maps) DESCRIPTION
Color-map files define the mapping between eight-bit color numbers and red, green and blue intensities used for those numbers. They are read by Magic as part of system startup, and also by the :load and :save commands in color-map windows. Color-map file names usually have the form x.y.z.cmapn, where x is a class of technology files, y is a class of displays, z is a class of monitors, and n is a version number (currently 1). The version number will change in the future if the formap of color-map files ever changes. Normally, x and y correspond to the corresponding parts of a display styles file. For example, the color map file mos.7bit.std.cmap1 is used today for most nMOS and CMOS technology files using displays that support at least seven bits of color per pixel and standard-phosphor monitors. It corresponds to the display styles file mos.7bit.dstyle5. Color-map files are stored in ASCII form, with each line containing four decimal integers separated by white space. The first three inte- gers are red, green, and blue intensities, and the fourth field is a color number. For current displays the intensities must be integers between 0 and 255. The color numbers must increase from line to line, and the last line must have a color number of 255. The red, green, and blue intensities on the first line are used for all colors from 0 up to and including the color number on that line. For other lines, the intensities on that line are used for all colors starting one color above the color number on the previous line and continuing up and through the color number on the current line. For example, consider the color map below: 255 0 0 2 0 0 255 3 255 255 255 256 This color map indicates that colors 0, 1, and 2 are to be red, color 3 is to be blue, and all other colors are to be white. SEE ALSO
magic(1), dstyle(5) 4th Berkeley Distribution CMAP(5)
All times are GMT -4. The time now is 03:10 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy