You're going to need to install gcc and your kernel source. I think you're going to be doing your work in a terminal, not any sort of IDE. Compiling code for the kernel is very different from compiling code for your system.
Following this tutorial I was able to create a do-nothing character driver, but had to modify their instructions slightly:
...what this is doing is telling make to use the makefile that came with your kernel (in my case stored in /usr/src/linux/Makefile) to compile your source, which spares you a lot of headaches. That M variable tells it where to find your own makefile once it's set up.
I think pwd vs ${pwd} was a typo in the magazine itself, but /usr/src/linux is just where my system keeps its kernel sources. Yours may be something else, or probably not even installed right now.
Note that a network driver is not a character driver. But I'd think they get built it the same way.
Last edited by Corona688; 10-20-2010 at 07:06 PM..
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi,
I found on linuxgazette.net/93/bhaskaran.html page very useful sample of virtual driver (not connected to real hardware).
I try to compile it with no effect.
So:
I got fresh Ubuntu 9.10 (kernel 2.6.31-14)
My source is saved in networkAdapter.c file in /usr/src/myModules directory.
I... (21 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
I installed Solaris 11.1 on a X86 PC. It's working except for one glaring problem : I cannot get a driver attached to the RaLink RT2800 (Wi Fi Adapter). Can someone point me in the direction where " the correct" driver exists, or let me know how I can tell Solaris to attach the device to the... (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
LEARN ABOUT DEBIAN
whereis
WHEREIS(1) User Commands WHEREIS(1)NAME
whereis - locate the binary, source, and manual page files for a command
SYNOPSIS
whereis [-bmsu] [-BMS directory... -f] filename...
DESCRIPTION
whereis locates source/binary and manuals sections for specified files. The supplied names are first stripped of leading pathname compo-
nents and any (single) trailing extension of the form .ext, for example, .c. Prefixes of s. resulting from use of source code control are
also dealt with. whereis then attempts to locate the desired program in a list of standard Linux places.
OPTIONS -b Search only for binaries.
-m Search only for manual sections.
-s Search only for sources.
-u Search for unusual entries. A file is said to be unusual if it does not have one entry of each requested type. Thus
`whereis -m-u *' asks for those files in the current directory which have no documentation.
-B Change or otherwise limit the places where whereis searches for binaries.
-M Change or otherwise limit the places where whereis searches for manual sections.
-S Change or otherwise limit the places where whereis searches for sources.
-f Terminate the last directory list and signals the start of file names, and must be used when any of the -B, -M, or -S options are
used.
EXAMPLE
Find all files in /usr/bin which are not documented in /usr/man/man1 with source in /usr/src:
example% cd /usr/bin
example% whereis -u -M /usr/man/man1 -S /usr/src -f *
FILES
/{bin,sbin,etc}
/usr/{lib,bin,old,new,local,games,include,etc,src,man,sbin,
X386,TeX,g++-include}
/usr/local/{X386,TeX,X11,include,lib,man,etc,bin,games,emacs}
SEE ALSO chdir(2V)BUGS
Since whereis uses chdir(2V) to run faster, pathnames given with the -M, -S, or -B must be full; that is, they must begin with a `/'.
whereis has a hard-coded path, so may not always find what you're looking for.
AVAILABILITY
The whereis command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux July 2009 WHEREIS(1)