Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: How to check which NIC Card is used for backups?
Operating Systems Linux How to check which NIC Card is used for backups? Post 302464226 by DGPickett on Tuesday 19th of October 2010 02:19:06 PM
Old 10-19-2010
Code:
 netstat(1)                                                       netstat(1)

           -i                Show the state of network interfaces.  Only the
                             interfaces that have been configured with an IP
                             address or the plumb option using the ifconfig
                             command are shown.  The output includes both
                             the primary and logical interfaces.  (See
                             ifconfig(1M)).  The counts for Ipkts and Opkts
                             fields are for IP packets only.  This option is
                             ignored if the -p option is specified.

           -I interface      Show information about the specified interface
                             only.  This option applies to the -g and -i
                             options.



---------- Post updated at 02:19 PM ---------- Previous update was at 02:18 PM ----------

lsof will verify where what process has what socket open to.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies

2. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies

3. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies

4. Solaris

How to check Virtual NIC card speed on solaris

Hi, We have a 4 port Sun gigaswift NIC card on our sun fire server. If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings. Details ----------- root:/> ifconfig -a lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies

5. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

6. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies

7. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies

8. UNIX for Advanced & Expert Users

Determine the ethernet (NIC) card speed.

Hi, Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux. I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies

9. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies

LEARN ABOUT X11R4

inet_type

inet_type(4)                                                       File Formats                                                       inet_type(4)

NAME

       inet_type - default Internet protocol type

SYNOPSIS

       /etc/default/inet_type

DESCRIPTION

       The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.

       The  inet_type  file  can  contain  a  number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
       assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.

       The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file.  By  default,
       both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
       setting the value of DEFAULT_IP.  The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
       will be displayed:

       IP_VERSION4     Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
                       and netstat(1M) commands.

       IP_VERSION6     Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       BOTH            Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For  example,
       even if the value of DEFAULT_IP is IP_VERSION4, the command

       example% ifconfig -a6

       will display all IPv6 interfaces.

EXAMPLES

       Example 1: Suppressing IPv6 Related Output

       This is what the inet_type file must contain if you want to suppress IPv6 related output:

       DEFAULT_IP=IP_VERSION4

SEE ALSO

       ifconfig(1M), netstat(1M)

SunOS 5.10                                                          16 Jun 1999                                                       inet_type(4)
All times are GMT -4. The time now is 11:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy