All
Please help, i will telnet to router to obain the ping status and compare, if higher than normal latency, i will have further action..
if i do the telent and in perl script then ....
e.g the result i obtain from the router will be =' Success rate is 100 percent (5/5), round-trip... (4 Replies)
Somewhat long story:
I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage.
This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only... (1 Reply)
This Expect script provides expect with a list of IP addresses to Cisco IPS sensors and commands to configure Cisco IPS sensors. The user, password, IP addresses, prompt regex, etc. have been anonymized. In general this script will log into the sensors and send commands successfully but there are... (1 Reply)
Hi Experts,
I am using perl to telnet on cisco boxes. We have this stupid cisco node which does not support "terminal Length0" command.
Since I am using Net::Telnet and capturing output with
@output = $telnet->cmd('cmd');
Say
@output = $telnet->cmd('show version');
Now problem... (2 Replies)
I am writing perl script to configure Cisco device but Variables inside Net::Telnet::Cisco Module doesn't work and passed to device without resolving.
Please advise.
here is a sample of script:
use Net::Telnet::Cisco;
$device = "10.14.199.1";
($o1, $o2, $o3, $o4) = split(/\./,$device);... (5 Replies)
Hi all,
I use a bash script which use expect to connect throught ssh and run command on a cisco router. The ssh connection with expect work fine, but the first command on the cisco router failed,
I try to run the command in error by hand and it work fine... :(
the first part of the script... (2 Replies)
Hi all
i have little problem finding solution about simple telnet script .... i have 250 routers and on some i have different password and on some they ask just for password no username. So for example 1,2,3 have username and password (user,password) 4, and 5 have different username and password... (0 Replies)
I know there are better ways to do this.
I prefer snmp. I do not have the proper perl modules loaded on the platorm. Snmp isnt loaded on the platform. Telnet is not an option. I need to write an expect script to pull cisco equipment configs.
The following code is executed once I gain... (0 Replies)
HI all
i need to connect to about 900 cisco routers and switch to do some configs changes. the issue i am having is that half the devices have one set of username and password and the other half have another username and password. From expect or bash script i can ssh into a device and make... (0 Replies)
Discussion started by: quintin
0 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)