Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)