Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
locale::script
Locale::Script(3perl) Perl Programmers Reference Guide Locale::Script(3perl)NAME
Locale::Script - standard codes for script identification
SYNOPSIS
use Locale::Script;
$script = code2script('phnx'); # 'Phoenician'
$code = script2code('Phoenician'); # 'Phnx'
$code = script2code('Phoenician',
LOCALE_CODE_NUMERIC); # 115
@codes = all_script_codes();
@scripts = all_script_names();
DESCRIPTION
The "Locale::Script" module provides access to standards codes used for identifying scripts, such as those defined in ISO 15924.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 15924
four-letter codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying scripts. The ones currently supported are:
alpha
This is a set of four-letter (capitalized) codes from ISO 15924 such as 'Phnx' for Phoenician.
This code set is identified with the symbol "LOCALE_SCRIPT_ALPHA".
The Zxxx, Zyyy, and Zzzz codes are not used.
This is the default code set.
numeric
This is a set of three-digit numeric codes from ISO 15924 such as 115 for Phoenician.
This code set is identified with the symbol "LOCALE_SCRIPT_NUMERIC".
ROUTINES
code2script ( CODE [,CODESET] )
script2code ( NAME [,CODESET] )
script_code2code ( CODE ,CODESET ,CODESET2 )
all_script_codes ( [CODESET] )
all_script_names ( [CODESET] )
Locale::Script::rename_script ( CODE ,NEW_NAME [,CODESET] )
Locale::Script::add_script ( CODE ,NAME [,CODESET] )
Locale::Script::delete_script ( CODE [,CODESET] )
Locale::Script::add_script_alias ( NAME ,NEW_NAME )
Locale::Script::delete_script_alias ( NAME )
Locale::Script::rename_script_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Script::add_script_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Script::delete_script_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes man page.
SEE ALSO
Locale::Codes
Locale::Constants
http://www.unicode.org/iso15924/
Home page for ISO 15924.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 1997-2001 Canon Research Centre Europe (CRE).
Copyright (c) 2001-2010 Neil Bowers
Copyright (c) 2010-2011 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.14.2 2011-09-26 Locale::Script(3perl)