Hey than alot! It is working fine. is it possible to continue the flow 191:391-391-591....?means if it didnt find any thing it should print 0 like [a1 391 591 0].
This should work
Last edited by Chubler_XL; 10-10-2010 at 08:27 PM..
Reason: Fix indenting
This User Gave Thanks to Chubler_XL For This Post:
sometimes in Solaris 8 when I go to mount filesystems using either the mount command or by editing the /etc/vfstab, i get a nice little error message saying the the number of allowable mount points has been exceeded. I have read man pages until I am blue in the face and no where can I find what the... (3 Replies)
I have a simple gnuplot question. I have a set of points (list of x,y,z values; irregularly spaced, i.e. no grid) that I want to plot. I want the plot to look like this:
- points in map view (no 3D view)
- color of each point should depend on its z-value.
- I want to define my own color scale
-... (0 Replies)
Hi,
I am trying to write a script to get entries between two points lets say start and end points from a log file,
the log file time format is as follows
Start - 07/Aug/2008:18:26:43
End - 07/Aug/2008:19:36:43
I tried using the following awk command but it couldnt pick up the entries... (3 Replies)
hi,
I believe a mount point does not have to be a physical disk, but rather a logical one? Is this correct? if so, how can I find out if my mount points are on different physical disks?
thanks (9 Replies)
Discussion started by: JamesByars
9 Replies
5. Post Here to Contact Site Administrators and Moderators
Hi folks,
I have been asked to performed the following:
Add the following new moint points systemA:/avp and SystemB:/usr/sap/trans to be the new linux server ZZZ
How can I add those mount points and how those mount points can become another linuz server?:wall::wall::wall: (2 Replies)
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Hi all,
I need to run a bunch of commands seperated by ; but then count the total lines of output. Pipes and redirection don't seem to be helping me. Anyone know how I can do this properly:
ls /usr/bin/nslookup ; ls /usr/sbin/lsof ; ls /sbin/ifconfig ; ls /usr/sbin/dmidecode ; ls... (2 Replies)
Hi,
I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches.
I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels)
But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies
LEARN ABOUT NETBSD
mixerctl.conf
MIXERCTL.CONF(5) BSD File Formats Manual MIXERCTL.CONF(5)NAME
mixerctl.conf -- audio mixer configuration file
SYNOPSIS
mixerctl.conf
DESCRIPTION
The /etc/mixerctl.conf file consists of mixerctl(1) variables to set at boot time. Each line of mixerctl.conf has the following format:
variable=value
To generate a mixerctl.conf from the current mixer settings, execute:
mixerctl -a > /etc/mixerctl.conf
Set mixerctl to YES in rc.conf(5) to have the variables set at boot time. Additionally, you can have the settings saved and restored for the
devices of your choice by listing them in mixerctl_mixers in rc.conf(5).
FILES
/etc/mixerctl.conf
EXAMPLES
Example mixer settings for an esa(4) audio adapter:
outputs.master=255,255
outputs.master.mute=off
outputs.mono=255
outputs.mono.mute=on
outputs.mono.source=mixerout
outputs.headphones=255,255
outputs.headphones.mute=off
outputs.tone=255,255
inputs.speaker=255
inputs.speaker.mute=off
inputs.phone=191
inputs.phone.mute=on
inputs.mic=191
inputs.mic.mute=on
inputs.mic.preamp=off
inputs.mic.source=mic0
inputs.line=191,191
inputs.line.mute=on
inputs.cd=191,191
inputs.cd.mute=on
inputs.video=255,255
inputs.video.mute=off
inputs.aux=255,255
inputs.aux.mute=off
inputs.dac=191,191
inputs.dac.mute=off
record.source=mic
record.volume=255,255
record.volume.mute=off
record.mic=0
record.mic.mute=off
outputs.loudness=off
outputs.spatial=off
outputs.spatial.center=0
outputs.spatial.depth=0
SEE ALSO mixerctl(1), rc.conf(5)HISTORY
The mixerctl.conf configuration file first appeared in NetBSD 2.0.
BSD April 5, 2003 BSD