Combine points of specific key (a1) based on user defined size (lets say 200 in this example).
so a1 191 and 191+200 and sum of all the values (4th column)
and vice versa...
sometimes in Solaris 8 when I go to mount filesystems using either the mount command or by editing the /etc/vfstab, i get a nice little error message saying the the number of allowable mount points has been exceeded. I have read man pages until I am blue in the face and no where can I find what the... (3 Replies)
I have a simple gnuplot question. I have a set of points (list of x,y,z values; irregularly spaced, i.e. no grid) that I want to plot. I want the plot to look like this:
- points in map view (no 3D view)
- color of each point should depend on its z-value.
- I want to define my own color scale
-... (0 Replies)
Hi,
I am trying to write a script to get entries between two points lets say start and end points from a log file,
the log file time format is as follows
Start - 07/Aug/2008:18:26:43
End - 07/Aug/2008:19:36:43
I tried using the following awk command but it couldnt pick up the entries... (3 Replies)
hi,
I believe a mount point does not have to be a physical disk, but rather a logical one? Is this correct? if so, how can I find out if my mount points are on different physical disks?
thanks (9 Replies)
Discussion started by: JamesByars
9 Replies
5. Post Here to Contact Site Administrators and Moderators
Hi folks,
I have been asked to performed the following:
Add the following new moint points systemA:/avp and SystemB:/usr/sap/trans to be the new linux server ZZZ
How can I add those mount points and how those mount points can become another linuz server?:wall::wall::wall: (2 Replies)
I have 2 physical interfaces (bnx0 and bnx1) aggregated into aggr1. I need to assign second IP, and normally I know how to do it to physical interface (i.e. bnx0:1) however same trick (aggr1:1) is not working. Is there any way to do it? (0 Replies)
Hi all,
I need to run a bunch of commands seperated by ; but then count the total lines of output. Pipes and redirection don't seem to be helping me. Anyone know how I can do this properly:
ls /usr/bin/nslookup ; ls /usr/sbin/lsof ; ls /sbin/ifconfig ; ls /usr/sbin/dmidecode ; ls... (2 Replies)
Hi,
I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches.
I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels)
But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)