09-23-2010
resetting the alom from the OS is not possible on a T2000. I've seen the issue you descripted a couple times and it looks related to the firmware version (6.7.4 or older). If you can take the system down without any issues, upgrading it to the current version (6.7.10) solves it (hopefully;-)) for the future.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Discussion started by: jsy
1 Replies
2. Solaris
Every time I would try to send a break to my T2000 I would get this
Debugging requested; hardware watchdog suspended.
c)ontinue, s)ync, r)eset?
I couldn't get into OBP.
Here's what I found to do...
sc> bootmode
Bootmode: normal
sc> bootmode reset_nvram
sc> bootmode... (3 Replies)
Discussion started by: mediis
3 Replies
3. Solaris
Hi,
I have forgot the sc and console login password in sun v125 server,
can anyone suggest me how to reset sc password in sun v125 server.
Thanks
Rjs (3 Replies)
Discussion started by: rajasekg
3 Replies
4. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
5. Solaris
Hi ,
How to reset ALOM/SC password for Solaris box Sun Fire T-200
Thanks (5 Replies)
Discussion started by: chetansingh23
5 Replies
6. Solaris
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Discussion started by: br1an
19 Replies
7. Solaris
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Discussion started by: rajasraf
1 Replies
8. Solaris
Hi,
How to set ip address on eth0 for access ssh from ALOM? Is it possible? Now i cannot access it because don't have VGA.
I keep try to access using ssh. Please guide me.
Thanks. (16 Replies)
Discussion started by: mzainal
16 Replies
9. Hardware
Hi all,
I have some problems with the fan FT0.F0, which looks like has a problem with the PROM/ALOM ( I am nor sure who).....but, in fact, the fan is working properly even in other V440 Sparc Server.
We checked HW comunication between Fan and the MotherBoard, and we think is a problem of... (8 Replies)
Discussion started by: proof_enrique
8 Replies
10. Solaris
Hi all,
I got a v215 but the login credentials are unknown. I plug the serial management RS232-RJ45 and get the output on the terminal. I reseted NVRAM and battery but I can't use the default login still. After these operations the output from boot is as such ;
ALOM POST 1.0
Status =... (21 Replies)
Discussion started by: y33t
21 Replies
LEARN ABOUT DEBIAN
astribank_hexload
ASTRIBANK_HEXLOAD(8) ASTRIBANK_HEXLOAD(8)
NAME
astribank_tool - Xorcom Astribank (xpp) firmware loader
SYNOPSIS
astribank_tool -D device-path -F [options] hexfile
astribank_tool -D device-path -p [options] hexfile1 .. hexfile4
astribank_tool -D device-path -O [-A] [options] imagefile
astribank_tool -D device-path -o [options]
astribank_tool -D device-path -E [options] hexfile
astribank_tool -h
DESCRIPTION
astribank_hexload is a second-stage firmware loader for Xorcom Astribanks. Note that some older models use fpga_load(8) instead.
It is used to load a file in the Intel HEX format into a Xorcom Astribank. It can be used to load either an FPGA firmware or a PIC
firmware. It is normally run by the script xpp_fxloader.
OPTIONS
-D device-path
Required. The device to read from/write to. This is bus_num/device_num, where bus_num and device_num are the first two numbers in
the output of lsusb(8) or dahdi_hardware(8). On older versions of this toolyou needed a complete path to the device, which would be
/dev/bus/usb/bus_num/device_num, or /proc/bus/usb/bus_num/device_num.
One of the following is required:
-F
The firmware to load is a FPGA firmware.
-p
The firmwares to load is are PIC firmwares. All (typically 4) should be on the command-line.
-O
The firmware to load is an Octasic echo canceller firmware image file.
-o
Don't load firmware. Just print the version number of the currently-loaded Octasic echo canceller firmware.
-E
The firmware to load is a special EEPROM burning one.
Other options:
-v
Increase verbosity. May be used multiple times.
-d mask
Set debug mask to mask. Default is 0, 0xFF is "everything".
-h
Displays usage message.
-A
When loading a Octasic echo canceller firmware, set the channels of the first Astribank module to use aLaw (G.711a). This is what
you'd normally use for BRI and E1. If not set, the default mu-Law (G.711u), which is what you'd normally use for FXS, FXO and T1.
SEE ALSO
fxload(8), lsusb(8), astribank_tool(8), fpga_load(8)
AUTHOR
This manual page was written by Tzafrir Cohen <tzafrir.cohen@xorcom.com> . Permission is granted to copy, distribute and/or modify this
document under the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL.
30 May 2011 ASTRIBANK_HEXLOAD(8)