Sponsored Content
Full Discussion: ipfw and dhcp
Top Forums UNIX for Advanced & Expert Users ipfw and dhcp Post 302454552 by frank_rizzo on Saturday 18th of September 2010 10:52:34 PM
Old 09-18-2010
Are you running two DHCP servers? use static DHCP entries - eg: configure their MAC addresses to get the same IP each time. I have done this with ISC DHCP.

where is PC2:le1 plugged into physically?
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

fBSD nat ipfw

i am running nat on my freeBSD and web/ftp server. The rule allow ip from any to any must always be? or how? if i accept all packets to go on my ep0 which diverts all to my intranet it doesnt help, must the rule allow ip from any to any always be ? even if many rules are between divert rule and... (3 Replies)
Discussion started by: hachik
3 Replies

2. Cybersecurity

ipfw directives and order of precidence...

Is there a general rule I can apply when examining/editing ipfw entries? Also, does each new entry have to have a unique rule number? And, I think I can write a script to block code red infected machines (though I'm not sure it would do more than slim down my web server error message log),... (0 Replies)
Discussion started by: [MA]Flying_Meat
0 Replies

3. BSD

ipfw slow ssh and ftp connections

just as the title says. thanks. #General Rule Sets /sbin/ipfw add 0300 check-state /sbin/ipfw add 0301 deny tcp from any to any in established /sbin/ipfw add 0302 pass tcp from any to any out setup keep-state /sbin/ipfw add 0303 pass udp from any to any out #SSH FTP /sbin/ipfw add 0400... (11 Replies)
Discussion started by: dwildgoose
11 Replies

4. UNIX for Dummies Questions & Answers

Need help with IPFW.. Please...

Hi folks, I am a Mac User, and have little knowledge on IPFW. I have a set up at home where my computer (with 2 ethernet cards and static IP adresses) serves Internet to my family's computers. I have already a script that will run automatically at login and called from Cron at certain... (2 Replies)
Discussion started by: fundidor
2 Replies

5. Cybersecurity

FreeBSD IPFW Rules clarification please...

Hello. I hope you can help me please. We are about to bring a few servers online which will be hosting different things... For one server, it will be hosting a HTTPd, and just wanted to know whether these rules are correct that I have? To ensure the right interfaces etc, here's a copy of... (1 Reply)
Discussion started by: DanUK
1 Replies

6. BSD

Using several pipes in ipfw (dummynet)

Hi! I've already posted this on the freebsd-questions mailing list, but I thought I could try it here too. I'm using FreeBSD 7.0 with IPFW DUMMYNET enabled. I've got a problem with creating a ruleset, which allows me to limit the overall bandwidth of a link and afterwards pass the packets... (0 Replies)
Discussion started by: xenator
0 Replies

7. Cybersecurity

pass syntax iptables to ipfw

Hello, excuse my English. Please could tell me how I can pass this syntax for iptables to ipfw. iptables -A OUTPUT -p tcp --dport 80 -m state --state NEW -m recent --set --name thor --rdest -j ACCEPT iptables -A INPUT -p tcp -m tcp --tcp-flag RST RST -m state --state ESTABLISHED -m recent... (0 Replies)
Discussion started by: dot357
0 Replies

8. Shell Programming and Scripting

Help, SSH /ipfw block script

Hello, This is an SSH Block hammer script using ipfw, that I have modified for my own use. It is for a freenas 7.2 box which is FreeBSD based. The script works, but if there is more then one hammer attack per day, my issue is the script reads the first five instances of refused or invalid... (2 Replies)
Discussion started by: dpreviti
2 Replies

9. IP Networking

Get DHCP relay interfaces IP address using DHCP

Hi All , please view the set up below: ------------------------------------------------------------------- | DHCP Server |-----------| ROUTER & |-----------| Clients | | 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X | ... (2 Replies)
Discussion started by: gdangoor
2 Replies

10. OS X (Apple)

How to enable ipfw.log?

Under Mountain Lion, I want logs from ipfw sent to ipfw.log instead of dumped in system.log I've tried to figure out how OSX handles logs, but... after going back and forth between a syslog.conf which does little if anything, a newsyslog.conf that seems to only handle rotation, an asl.conf that... (3 Replies)
Discussion started by: jnojr
3 Replies
dhcpmgr(1M)						  System Administration Commands					       dhcpmgr(1M)

NAME
dhcpmgr - graphical interface for managing DHCP service SYNOPSIS
/usr/sadm/admin/bin/dhcpmgr DESCRIPTION
dhcpmgr is a graphical user interface which enables you to manage the Dynamic Host Configuration Protocol (DHCP) service on the local sys- tem. It performs the functions of the dhcpconfig, dhtadm, and pntadm command line utilities. You must be root to use dhcpmgr. The dhcpmgr Help, available from the Help menu, contains detailed information about using the tool. USAGE
You can perform the following tasks using dhcpmgr: Configure DHCP service Use dhcpmgr to configure the DHCP daemon as a DHCP server, and select the data store to use for storing network configuration tables.. Configure BOOTP relay service Use dhcpmgr to configure the DHCP daemon as a BOOTP relay. Manage DHCP or BOOTP relay service Use dhcpmgr to start, stop, enable, disable or unconfigure the DHCP service or BOOTP relay service, or change DHCP server parameters. Manage DHCP addresses Use dhcpmgr to add, modify, or delete IP addresses leased by the DHCP service. Manage DHCP macros Use dhcpmgr to add, modify or delete macros used to supply configuration parameters to DHCP clients. Manage DHCP options Use dhcpmgr to add, modify or delete options used to define parameters deliverable through DHCP. Convert to a new DHCP data store Use dhcpmgr to configure the DHCP server to use a different data store, and convert the DHCP data to the format used by the new data store. Move DHCP data to another server Use dhcpmgr to export data from one Solaris DHCP server and import data onto another Solaris DHCP server. EXIT STATUS
The following exit values are returned: 0 Successful completion. non-zero An error occurred. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWdhcm | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
dhcpconfig(1M), dhtadm(1M), pntadm(1M), in.dhcpd(1M), dhcpsvc.conf(4), dhcp_network(4), dhcptab(4), attributes(5), dhcp(5), dhcp_modules(5) SunOS 5.11 13 Mar 2001 dhcpmgr(1M)
All times are GMT -4. The time now is 03:12 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy