I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any recommendations on where to start looking I would appreciate it.
Hi masters,
I am new to linux and unix forum and this is my first forum. So please excuse if
I am not giving sufficient information. I will give them on request.
I have created a bandwidth manager module. I am using a 2.6.9 kernel and in Red Hat 3.4.3 distribution. But when i run make... (1 Reply)
Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
I use command-line mode of GRUB to load kernel,
but I can not know how to chose the partition and kernel argument,
as followed :
please tell me how to do deal with ,
thanks! (0 Replies)
Greetings,
Does anyone know how to load AIX kernel extensions on reboot? I know that Oracle loads it's postwait kernel extension via a executable in /etc/inittab. I'm assuming this executable calls the "sysconfig" system call and loads it. What if I wrote my own? What is the proper way in AIX to... (3 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
I am trying to understand what are the differences of boot messages verbosity levels for the kernel field in grub.conf
From my research, there appear to be three levels:
quiet
verbose
debug
I have also found documents that specify removing quiet from the kernel field. If this is done, is... (1 Reply)
Hi,
I am running CentOS 6.5 and I want to remove auto loading 8021q and garp modules, but there are no configure files in /etc/modprobe.d define bot modules.
I even added both module names to /etc/modprobe.d/blacklist.conf, both of them are still loaded after the reboot. How can I disable... (2 Replies)
Hello,
Using Bash on Mac OS X 10.7.5 (Lion). I downloaded a GrowlSafari plugin for Webkit from its GitHub page GitHub - uasi/growl-safari-bridge: GrowlSafariBridge enables arbitrary javascript (including Safari Extensions) to notify via Growl.. In the description it says that after installing for... (0 Replies)
Discussion started by: scrutinizerix
0 Replies
LEARN ABOUT CENTOS
grub-file
GRUB-FILE(1) User Commands GRUB-FILE(1)NAME
grub-file - check file type
SYNOPSIS
file OPTIONS FILE
DESCRIPTION
Check if FILE is of specified type.
--is-i386-xen-pae-domu
Check if FILE can be booted as i386 PAE Xen unprivileged guest kernel
--is-x86_64-xen-domu
Check if FILE can be booted as x86_64 Xen unprivileged guest kernel
--is-x86-xen-dom0
Check if FILE can be used as Xen x86 privileged guest kernel
--is-x86-multiboot
Check if FILE can be used as x86 multiboot kernel
--is-x86-multiboot2 Check if FILE can be used as x86 multiboot2 kernel
--is-arm-linux
Check if FILE is ARM Linux
--is-arm64-linux
Check if FILE is ARM64 Linux
--is-ia64-linux
Check if FILE is IA64 Linux
--is-mips-linux
Check if FILE is MIPS Linux
--is-mipsel-linux
Check if FILE is MIPSEL Linux
--is-sparc64-linux
Check if FILE is SPARC64 Linux
--is-powerpc-linux
Check if FILE is POWERPC Linux
--is-x86-linux
Check if FILE is x86 Linux
--is-x86-linux32
Check if FILE is x86 Linux supporting 32-bit protocol
--is-x86-kfreebsd
Check if FILE is x86 kFreeBSD
--is-i386-kfreebsd
Check if FILE is i386 kFreeBSD
--is-x86_64-kfreebsd
Check if FILE is x86_64 kFreeBSD
--is-x86-knetbsd
Check if FILE is x86 kNetBSD
--is-i386-knetbsd
Check if FILE is i386 kNetBSD
--is-x86_64-knetbsd Check if FILE is x86_64 kNetBSD
--is-i386-efi
Check if FILE is i386 EFI file
--is-x86_64-efi
Check if FILE is x86_64 EFI file
--is-ia64-efi
Check if FILE is IA64 EFI file
--is-arm64-efi
Check if FILE is ARM64 EFI file
--is-arm-efi
Check if FILE is ARM EFI file
--is-hibernated-hiberfil
Check if FILE is hiberfil.sys in hibernated state
--is-x86_64-xnu
Check if FILE is x86_64 XNU (Mac OS X kernel)
--is-i386-xnu
Check if FILE is i386 XNU (Mac OS X kernel)
--is-xnu-hibr
Check if FILE is XNU (Mac OS X kernel) hibernated image
--is-x86-bios-bootsector
Check if FILE is BIOS bootsector
-h, --help Display this help and exit. -u, --usage Display the usage of this command and exit.
SEE ALSO
The full documentation for grub-file is maintained as a Texinfo manual. If the info and grub-file programs are properly installed at your
site, the command
info grub-file
should give you access to the complete manual.
grub-file (GRUB) 2.02-2ubuntu8.3 July 2018 GRUB-FILE(1)