I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any recommendations on where to start looking I would appreciate it.
Hi masters,
I am new to linux and unix forum and this is my first forum. So please excuse if
I am not giving sufficient information. I will give them on request.
I have created a bandwidth manager module. I am using a 2.6.9 kernel and in Red Hat 3.4.3 distribution. But when i run make... (1 Reply)
Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
I use command-line mode of GRUB to load kernel,
but I can not know how to chose the partition and kernel argument,
as followed :
please tell me how to do deal with ,
thanks! (0 Replies)
Greetings,
Does anyone know how to load AIX kernel extensions on reboot? I know that Oracle loads it's postwait kernel extension via a executable in /etc/inittab. I'm assuming this executable calls the "sysconfig" system call and loads it. What if I wrote my own? What is the proper way in AIX to... (3 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
I am trying to understand what are the differences of boot messages verbosity levels for the kernel field in grub.conf
From my research, there appear to be three levels:
quiet
verbose
debug
I have also found documents that specify removing quiet from the kernel field. If this is done, is... (1 Reply)
Hi,
I am running CentOS 6.5 and I want to remove auto loading 8021q and garp modules, but there are no configure files in /etc/modprobe.d define bot modules.
I even added both module names to /etc/modprobe.d/blacklist.conf, both of them are still loaded after the reboot. How can I disable... (2 Replies)
Hello,
Using Bash on Mac OS X 10.7.5 (Lion). I downloaded a GrowlSafari plugin for Webkit from its GitHub page GitHub - uasi/growl-safari-bridge: GrowlSafariBridge enables arbitrary javascript (including Safari Extensions) to notify via Growl.. In the description it says that after installing for... (0 Replies)
Discussion started by: scrutinizerix
0 Replies
LEARN ABOUT MOJAVE
installgrub
installgrub(1M)installgrub(1M)NAME
installgrub - install GRUB in a disk partition or a floppy
SYNOPSIS
/sbin/installgrub [-fm] stage1 stage2 raw-device
The installgrub command is an -only program. GRUB stands for GRand Unified Bootloader.
installgrub installs GRUB stage 1 and stage 2 files on the boot area of a disk partition. If you specify the -m option, installgrub
installs the stage 1 file on the master boot sector of the disk.
The installgrub command accepts the following options:
-f
Suppresses interaction when overwriting the master boot sector.
-m
Installs GRUB stage1 on the master boot sector interactively.
The installgrub command accepts the following operands:
stage1
The name of the GRUB stage 1 file.
stage2
The name of the GRUB stage 2 file.
raw-device
The name of the device onto which GRUB code is to be installed. It must be a character device that is readable and writable. For disk
devices, specify the slice where the GRUB menu file is located. (For Solaris it is the root slice.) For a floppy disk, it is
/dev/rdiskette.
Example 1: Installing GRUB on a Hard Disk Slice
The following command installs GRUB on a system where the root slice is c0d0s0:
example# /sbin/installgrub /boot/grub/stage1
/boot/grub/stage2 /dev/rdsk/c0d0s0
Example 2: Installing GRUB on a Floppy
The following command installs GRUB on a formatted floppy:
example# mount -F pcfs /dev/diskette /mnt
# mkdir -p /mnt/boot/grub
# cp /boot/grub/* /mnt/boot/grub
# umount /mnt
# cd /boot/grub
# /sbin/installgrub stage1 stage2 /dev/rdiskette
/boot/grub
Directory where GRUB files reside.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
boot(1M), fdisk(1M), fmthard(1M), kernel(1M), attributes(5)
Installing GRUB on the master boot sector (-m option) overrides any boot manager currently installed on the machine. The system will always
boot the GRUB in the Solaris partition regardless of which fdisk partition is active.
24 May 2005 installgrub(1M)