I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any recommendations on where to start looking I would appreciate it.
Hi masters,
I am new to linux and unix forum and this is my first forum. So please excuse if
I am not giving sufficient information. I will give them on request.
I have created a bandwidth manager module. I am using a 2.6.9 kernel and in Red Hat 3.4.3 distribution. But when i run make... (1 Reply)
Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2.
also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
I use command-line mode of GRUB to load kernel,
but I can not know how to chose the partition and kernel argument,
as followed :
please tell me how to do deal with ,
thanks! (0 Replies)
Greetings,
Does anyone know how to load AIX kernel extensions on reboot? I know that Oracle loads it's postwait kernel extension via a executable in /etc/inittab. I'm assuming this executable calls the "sysconfig" system call and loads it. What if I wrote my own? What is the proper way in AIX to... (3 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
I am trying to understand what are the differences of boot messages verbosity levels for the kernel field in grub.conf
From my research, there appear to be three levels:
quiet
verbose
debug
I have also found documents that specify removing quiet from the kernel field. If this is done, is... (1 Reply)
Hi,
I am running CentOS 6.5 and I want to remove auto loading 8021q and garp modules, but there are no configure files in /etc/modprobe.d define bot modules.
I even added both module names to /etc/modprobe.d/blacklist.conf, both of them are still loaded after the reboot. How can I disable... (2 Replies)
Hello,
Using Bash on Mac OS X 10.7.5 (Lion). I downloaded a GrowlSafari plugin for Webkit from its GitHub page GitHub - uasi/growl-safari-bridge: GrowlSafariBridge enables arbitrary javascript (including Safari Extensions) to notify via Growl.. In the description it says that after installing for... (0 Replies)
Discussion started by: scrutinizerix
0 Replies
LEARN ABOUT SUNOS
modules-load.d
MODULES-LOAD.D(5) modules-load.d MODULES-LOAD.D(5)NAME
modules-load.d - Configure kernel modules to load at boot
SYNOPSIS
/etc/modules-load.d/*.conf
/run/modules-load.d/*.conf
/usr/lib/modules-load.d/*.conf
DESCRIPTION systemd-modules-load.service(8) reads files from the above directories which contain kernel modules to load during boot in a static list.
Each configuration file is named in the style of /etc/modules-load.d/program.conf. Note that it is usually a better idea to rely on the
automatic module loading by PCI IDs, USB IDs, DMI IDs or similar triggers encoded in the kernel modules themselves instead of static
configuration like this. In fact, most modern kernel modules are prepared for automatic loading already.
CONFIGURATION FORMAT
The configuration files should simply contain a list of kernel module names to load, separated by newlines. Empty lines and lines whose
first non-whitespace character is # or ; are ignored.
CONFIGURATION DIRECTORIES AND PRECEDENCE
Configuration files are read from directories in /etc/, /run/, and /lib/, in order of precedence. Each configuration file in these
configuration directories shall be named in the style of filename.conf. Files in /etc/ override files with the same name in /run/ and
/lib/. Files in /run/ override files with the same name in /lib/.
Packages should install their configuration files in /lib/. Files in /etc/ are reserved for the local administrator, who may use this logic
to override the configuration files installed by vendor packages. All configuration files are sorted by their filename in lexicographic
order, regardless of which of the directories they reside in. If multiple files specify the same option, the entry in the file with the
lexicographically latest name will take precedence. It is recommended to prefix all filenames with a two-digit number and a dash, to
simplify the ordering of the files.
If the administrator wants to disable a configuration file supplied by the vendor, the recommended way is to place a symlink to /dev/null
in the configuration directory in /etc/, with the same filename as the vendor configuration file. If the vendor configuration file is
included in the initrd image, the image has to be regenerated.
EXAMPLE
Example 1. /etc/modules-load.d/virtio-net.conf example:
# Load virtio-net.ko at boot
virtio-net
SEE ALSO systemd(1), systemd-modules-load.service(8), systemd-delta(1), modprobe(8)systemd 237MODULES-LOAD.D(5)