Hi people.
Don't know if you could help me, but here it goes anyway.
I need to search for some directories, and if i for any file founded a must run another Bat file.
Can this be done in DOS ?
Thanks in advance (1 Reply)
Hi,
In a kshell , i need to compare the results of two array .
each Non-match value should copy to a new array.
For example:
==========
Array one contain the following values:
A
B
C
Array two contain the following values:
C
F
A
E
After comparing this arrays , a new array should... (4 Replies)
How can I send the results of a query to a unix variable. I basically want to run a query then do some logic on the results. Trying to redirect the result into a variable I define in the script.
select count(*) as counter from table - nut to redirect the "count" returned from the query... (2 Replies)
Hello,
I am working with KSH on AIX and I have 2 files generated from different sources... as seen below:
FILE1 FILE2
AAA AAA@ABS0001C
BBB BBB@ABS0003D
CCC CCC@ABS0023A
DDD DDD@ABC0145D
EEE EEE@ABS0090A
FFF FFF@ABS0002A
GGG GGG@ABC0150D
HHH
FILE1 is main main data source,... (4 Replies)
Hi ,
I am not familiar with shell programming. I have a requirement like i have two files
.I need to compare the two files by comparing each parameter and i should produce 2 outputs.
1)i have around 35 parameters say i have one parameter name called db_name=dcap in one file and... (7 Replies)
Here is one I am baffled with; I have not used unix for a while and now that I am back it has been fun remembering and I have enjoyed it, for the most past. this is in ksh.
I need to search in a file for the line with X1 and cut columns 20-25, put them into a variable, added them (dollar... (3 Replies)
Hi all,
I am posting the thread similar to previous posts but here my scenario is i need to know what the files size from start date. Here end time file size will be 0. Also need to know how much time does it took to complete in seconds.
log file:
Name1 START 11:36:45 ... (5 Replies)
Hello All,
I'm working on a script that will actually read a file consisting of data like the below:(ReportID,Sub_reportID,Sub_reportName)
1,1,ABC
1,2,DEF
1,3,GHI
2,1,JKL
2,2,MNO
3,1,PQR
I want to read the Sub Report details for a Report_ID using while loop and write these values into... (6 Replies)
In the below bash I am trying to read each file from a specific directory into a variable REF or VAL. Then use those variables in an awk to compare each matching file from REF and VAL. The filenames in the REF are different then in the VAL, but have a common id up until the _ I know the awk portion... (15 Replies)
Good morning all,
This is the file name in question OD_Orders_2019-02-19.csv
I am trying to create a bash script to read into files with yesterdays date on the file name while retaining the rest of the files name. I would like for $y to equal, the name of the file with a formula output with... (2 Replies)
Discussion started by: Ibrahim A
2 Replies
LEARN ABOUT LINUX
stopping
stopping(7) Miscellaneous Information Manual stopping(7)NAME
stopping - event signalling that a job is stopping
SYNOPSIS
stopping JOB=JOB INSTANCE=INSTANCE RESULT=RESULT [PROCESS=PROCESS] [EXIT_STATUS=STATUS] [EXIT_SIGNAL=SIGNAL] [ENV]...
DESCRIPTION
The stopping event is generated by the Upstart init(8) daemon when an instance of a job begins stopping. The JOB environment variable con-
tains the job name, and the INSTANCE environment variable contains the instance name which will be empty for single-instance jobs.
If the job is stopping normally, the RESULT environment variable will be ok, otherwise if the job is stopping because it has failed it will
be failed.
When the job has failed, the process that failed will be given in the PROCESS environment variable. This may be pre-start, post-start,
main, pre-stop or post-stop; it may also be the special value respawn to indicate that the job is stopping because it hit the respawn
limit.
Finally in the case of a failed job, one of either EXIT_STATUS or EXIT_SIGNAL may be given to indicate the cause of the stop. Either
EXIT_STATUS will contain the exit status code of the process, or EXIT_SIGNAL will contain the name of the signal that the process received.
The normal exit job configuration stanza can be used to prevent particular exit status values or signals resulting in a failed job, see
init(5) for more information.
If neither EXIT_STATUS or EXIT_SIGNAL is given for a failed process, it is because the process failed to spawn (for example, file not
found). See the system logs for the error.
init(8) will wait for all services started by this event to be running, all tasks started by this event to have finished and all jobs
stopped by this event to be stopped before allowing the job to continue stopping.
This allows jobs to depend on other jobs, safely stopping themselves before their dependency goes away. This event is typically combined
with the started(7) event by services.
Job configuration files may use the export stanza to export environment variables from their own environment into the stopping event. See
init(5) for more details.
EXAMPLE
A service that wishes to depend on another service might use:
start on started apache
stop on stopping apache
A task that must be run before another task or service is stopped might use:
start on stopping postgresql RESULT=ok
SEE ALSO starting(7)started(7)stopped(7)init(5)Upstart 2009-07-09 stopping(7)