Hi Guys
i have two servers which are n cluster prd1 and prd2.. I already have a metaset configured in it..My job was to create a 1.8 tb LUN in my storage which is having Hardware raid5 pre-configured..i Created 1.8 tb with raid 5 in my storage and it got detected in both t servers prd1... (4 Replies)
hi all,
i am using solaris 5.10 on sun blade 150 and i am trying to configure diskset in sun volume manager. When i fire the following command, it says some rpc related error.
bash-3.00# metaset -s kingston -a -h u15_9
metaset: u15_9: metad client create: RPC: Program not registered
how to... (4 Replies)
The following is the summarry:-
1) Four disks in server ie (c1t0d0. c1t1d0, c1t2d0, c1t3d0). c1t2d0 is the disk to be replaced.
c1t0d0 and c1t2d0 are mirrors.
c1t1d0 and c1t3d0 are mirrors.
Metadb to be deleted is in c1t2d0s7
a) Mirror d35 has 2 submirrors d38 and d39
d38 is a stripe... (0 Replies)
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Hi guys,
currently I'm working on one problem. I have Sol10 box where I need to replace old storage for the new one with minimal downtime.
Layout of metadevice looks like this:
d103 p 1.0GB d100
d102 p 2.0GB d100
d101 p 1.0GB d100
d100 s ... (3 Replies)
Hi all,
can somebody provide me with advice if is possible to replace physical LUN, with soft partitions (located directly on LUN, not on metadevice) by the new one.
Current state looks like this:
root@xxx:/etc/zones # metastat -c| egrep -i 900bec2d286
d504 p 159GB... (1 Reply)
Dear all,
This metaset stuff drive me crazy.
The story begin with the Solaris 8 upgrade....
We have a pair of Solaris 8 with Sun Cluster 3.1, to prevent a long downtime, the Live Upgrade was chosen. As metadb cannot use LU to upgrade directly, we remove the diskset before upgrade, and put it... (0 Replies)
I am using Solaris 9 (Sparc based) with Sybase and a proprietary DB application that works with Sybase. In the past we have not used SVM or any RAID config. The DBs were configured such that each DB had its own partition.
Now I would like to setup a new machine with the DBs on a RAID5 config... (1 Reply)
Discussion started by: DavidC_SysEngr
1 Replies
LEARN ABOUT SUSE
partx
PARTX(8) System Manager's Manual PARTX(8)NAME
partx - telling the kernel about presence and numbering of on-disk partitions.
SYNOPSIS
partx [-a|-d|-l] [--type TYPE] [--nr M-N] [partition] disk
DESCRIPTION
Given a block device ( disk ) and a partition table type , try to parse the partition table, and list the contents. Optionally add or
remove partitions.
This is not an fdisk - adding and removing partitions is not a change of the disk, but just telling the kernel about presence and numbering
of on-disk partitions.
OPTIONS -a add specified partitions or read disk and add all partitions
-d delete specified or all partitions
-l list partitions. Note that the all numbers are in 512-byte sectors.
--type TYPE
Specify the partition type -- dos, bsd, solaris, unixware or gpt.
--nr M-N
Specify the range of partitions (e.g --nr 2-4).
SEE ALSO addpart(8), delpart(8), fdisk(8), parted(8), partprobe(8)AVAILABILITY
The partx command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.
11 Jan 2007 PARTX(8)