08-12-2010
IBM Server doesn't ping gateway unless you put a static route
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks in Advance,
--witt
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have a machine that sits on 10.2 network.
I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs
what should I need to do?
Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies
2. HP-UX
I want to make static route how would I proceed?
I'm using "route add DestinationIP gatewayIP hop to 1
I would like to make this permanent, so when it reboots I don't want to loose it, would I do this in netconf file? If so where?
I did a search got this site, it didn't help much. ... (2 Replies)
Discussion started by: catwomen
2 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Request you to please tell me the command or the process to add the static route in redhat linux.
Thanks in Advance.
Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
4. AIX
#netstat -nr (shows the following with more static routes)
192.168.18.202 10.129.155.1 UGH 0 29 en0 - -
and i just want to remove the above one
i tried
#smitty rmroute
destination type= net
dest add = 192.168.18.202
default gateway= 10.129.155.1
net... (1 Reply)
Discussion started by: pchangba1
1 Replies
5. IP Networking
Hi guys,
sorry for asking noob question.
When do we really need to add a static route on the server?
I encounter this situation whereby a client trigger a network packet to the destination but the destination does not know how to return the traffic back to the client (source).
The issue was... (4 Replies)
Discussion started by: DrivesMeCrazy
4 Replies
6. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
7. AIX
Anyone know how to edit a static route in AIX? I find myself deleting and then recreating the route with the new information. Would be nice to know how to edit the route. (3 Replies)
Discussion started by: bbbngowc
3 Replies
8. Red Hat
Hello Guys..
I am facing this weird problem of static route not added after reboot!!
Following is my route-<interface> file..
# cat /etc/sysconfig/network-scripts/route-eth0
ADDRESS0=172.31.0.1
NETMASK0=255.255.255.255
GATEWAY0=192.168.208.1
ADDRESS1=172.31.15.2... (3 Replies)
Discussion started by: parth_buch
3 Replies
9. IP Networking
Hi all,
This may be the basic question of Routing but I am a sort of new to networking so I am asking.
Do I need to put route for my router's LAN port ip to WAN (serial) port ip Or the router itself can communicate between its ports without routes.
lan (172.26.40.5) ... (3 Replies)
Discussion started by: dextergenious
3 Replies
10. Red Hat
Can somebody know if it is possible to connect to remote IBM MQ, if local server using C, but don't have MQ library?
Thanks for contribution (0 Replies)
Discussion started by: digioleg54
0 Replies
LEARN ABOUT NETBSD
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-adIlnrv] [-A as_server] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-A Turn on AS# lookups and use the given server instead of the default.
-a Turn on AS# lookups for each hop encountered.
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached net-
work, an error is returned. This option can be used to send probes to a local host through an interface that has no route through it
(e.g., after the interface was dropped by route6d(8)).
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
EXIT STATUS
The traceroute6 command exits 0 on success, and >0 on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
September 17, 2005 BSD